Skip to main content

AOVX - AG300 Configuration

This page covers the public configuration context for using the AOVX AG300 with Plaspy. It focuses on the server details, setup flow, and the practical commands that are publicly available for preparing the tracker to communicate with the platform.

Plaspy uses shared server settings across supported devices, and it automatically detects the tracker protocol after the device connects. The exact manufacturer-side setup steps can still vary depending on firmware, hardware revision, installation type, and the tools provided by AOVX.

Configuration Overview​

The AOVX AG300 configuration process is intended to point the tracker to the Plaspy server, confirm the device is using the correct connection settings, and make sure the unit can report data reliably. Once the tracker is sending messages to the shared Plaspy endpoint, the platform can identify the protocol and begin processing the incoming events.

  • Prepare the tracker so it can communicate with the Plaspy server endpoint.
  • Enter the shared Plaspy host and port values used by supported devices.
  • Select the correct transport method if the device requires UDP or TCP.
  • Apply the carrier and reporting parameters needed for initial communication.
  • Validate that the tracker is actively reporting after configuration is saved.
  • Use Plaspy visibility tools to confirm the device appears online and begins transmitting data.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol after the device connects
  • All supported devices in Plaspy use the same port

Typical Requirements Before Setup​

  • Confirm the tracker is powered and ready for configuration.
  • Have access to the official AOVX configuration method or software.
  • Verify that the device can be edited with the available manufacturer workflow.
  • Prepare the public Plaspy server details before starting the setup.
  • Make sure the installation environment allows the tracker to communicate normally.
  • Review the latest AOVX documentation for any model-specific setup notes.

How This Tracker Connects to Plaspy​

The AG300 connects by sending its tracker data to the shared Plaspy server endpoint on port 8888. After the device is pointed to d.plaspy.com or the server IP 54.85.159.138, Plaspy receives the incoming connection, identifies the protocol automatically, and starts processing the tracker messages.

  • The tracker is configured to report to the shared Plaspy server rather than a device-specific endpoint.
  • UDP or TCP may be used on port 8888 depending on the manufacturer configuration method.
  • Once traffic reaches Plaspy, the platform automatically detects the tracker protocol.
  • Location and device events can then be displayed in the Plaspy interface for monitoring.
  • Ongoing reporting supports operational visibility and history review in Plaspy.
  • If the device requires a restart after saving settings, it should reconnect using the stored server details.

Common Configuration Workflow​

  1. Open the official AOVX configuration method or software for the AG300.
  2. Enter the Plaspy server domain d.plaspy.com or the server IP 54.85.159.138.
  3. Set the port to 8888.
  4. Choose UDP or TCP if the device asks for a transport selection.
  5. Apply or save the configuration so the tracker stores the new server details.
  6. Restart the device if the manufacturer workflow requires it.
  7. Confirm that the tracker begins reporting to Plaspy and appears in the platform.
  8. If needed, review the saved settings again to verify the server and reporting values.

Example Configuration Commands​

The public setup flow for the AG300 includes SMS configuration commands for APN, server, reporting interval, and data mode. The placeholders in the APN command represent your carrier values.

  • Configure the carrier APN
APN,{{apn}}#

If your carrier requires a username and password, the optional placeholders are included in the same command format.

APN,{{apn}},{{apnu}},{{apnp}}#
  • Set the GPRS server to Plaspy
SERVER,1,d.plaspy.com,8888,0#
  • Set the update interval
TIMER,60,60#
  • Switch the tracker to GPRS mode
GPRSON,1#
  • Check the saved configuration
PARAM#
  • Check tracker status
STATUS#

Configuration Notes​

  • Public configuration commands can vary slightly by firmware version or regional device release.
  • The AG300 may support SMS-based setup in addition to the manufacturer’s own tools or workflows.
  • Plaspy uses the same port for all supported devices, which simplifies server-side setup.
  • UDP and TCP options should be selected according to the device’s configuration interface and the public setup method available.
  • Always confirm the saved values after configuration to make sure the tracker is using the Plaspy server details correctly.

Why Use Plaspy with This Configuration​

Using the AOVX AG300 with Plaspy provides a practical way to centralize asset visibility, event monitoring, and long-term tracking in one platform. The shared Plaspy server settings and automatic protocol detection help reduce integration complexity while still keeping the setup approach aligned with standard manufacturer workflows.

For organizations that need dependable asset oversight, the AG300 can be configured to report into Plaspy using the same public server endpoint and port used by other supported devices. To learn more about Plaspy, visit https://www.plaspy.com. For the latest device-specific setup details, firmware behavior, and manufacturer guidance, please verify the current information on the official AOVX website at https://www.aovx.com/.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy