Skip to main content

Aplicom - A9 Quick Configuration

This page documents the public configuration context for using the Aplicom A9 Quick with Plaspy. It explains the shared server settings and practical setup steps you will commonly use when preparing the A9 Quick for connection to Plaspy. The guidance here is based on public Plaspy settings and the A9 Quick device description such as its plug and play form factor, internal GSM and GNSS antennas, and optional use with the Aplicom 3PAD keypad.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, but manufacturer-side steps can vary. Exact configuration actions on the A9 Quick may differ with firmware version, hardware revision, installation type, and vendor configuration tools, so use this page as a practical public reference and verify device specific details with the manufacturer when needed.

Configuration Overview​

The goal of this configuration process is to prepare the A9 Quick so it can reliably communicate with Plaspy and appear as an active device in the platform. Use the shared Plaspy endpoint and port during device configuration, confirm connectivity from the tracker to the network, and validate reporting in Plaspy.

  • Configure the device to send telemetry to the Plaspy server endpoint so the platform can receive location and event data.
  • Ensure the unit has power and cellular connectivity so it can establish a data session and transmit messages.
  • Select the appropriate transport type (UDP or TCP) on the device if required and set the shared Plaspy port.
  • Save and apply settings on the A9 Quick and restart the unit if the manufacturer procedure requires it.
  • Validate the device appears and reports correctly in Plaspy, using the platform to confirm telemetry and events.

Plaspy Server Settings​

Use the following public Plaspy connection settings when configuring the Aplicom A9 Quick:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol

Note that Plaspy uses the same port for all supported devices and will detect the tracker protocol automatically once the device is sending data to the endpoint above.

Typical Requirements Before Setup​

  • A powered A9 Quick unit installed or plugged into the vehicle power source such as the cigarette lighter socket.
  • An active SIM card with a data plan and correct APN settings for the mobile network in your region.
  • Access to the official Aplicom configuration method or software recommended by the vendor for the A9 Quick.
  • A Plaspy service account or access via your Plaspy administrator so you can verify device reporting in the platform.
  • Knowledge of the device firmware version and any vendor notes that affect configuration steps or commands.
  • If using the Aplicom 3PAD keypad, have the accessory connected and tested per the vendor instructions before final validation.

How This Tracker Connects to Plaspy​

When configured, the A9 Quick sends location and event data to the shared Plaspy server endpoint and port so Plaspy can process telemetry and present it in the platform. Plaspy’s automatic protocol detection simplifies server-side handling and lets the same server settings work across many tracker models.

  • The A9 Quick is set to report to d.plaspy.com or 54.85.159.138 on port 8888.
  • Choose UDP or TCP transport on the device if the configuration requires a transport selection.
  • Plaspy automatically detects the tracker protocol when data arrives at the shared port.
  • Once reporting begins, Plaspy receives position updates, movement events, and other device messages for visibility and monitoring.
  • Validate device activity in Plaspy to confirm the tracker is online and sending expected messages.

Common Configuration Workflow​

  1. Prepare the device by ensuring the A9 Quick is powered and the SIM is active with data and correct APN settings.
  2. Access the official Aplicom configuration method or software as provided by the manufacturer or installer.
  3. Enter the Plaspy server address by using either d.plaspy.com or the server IP 54.85.159.138 in the device server settings.
  4. Set the device port to 8888 as the destination port used by Plaspy for all devices.
  5. If the device requires transport selection, choose UDP or TCP according to your installation preference or vendor guidance.
  6. Apply or save the configuration on the device and restart the A9 Quick if the manufacturer tool indicates a restart is required.
  7. Validate that the device reports to Plaspy by checking device activity and incoming telemetry in your Plaspy account.

Example Configuration Commands​

The exact commands and configuration method for the A9 Quick depend on the Aplicom configuration utility, firmware, or the vendor installation tool you are using. Aplicom often provides configuration via their software or vendor tools which may use a graphical interface or command syntax. Because methods vary by firmware and toolchain, consult the Aplicom configuration guide or your vendor for the precise commands and field locations required to set server, port, and transport.

If you have vendor supplied command examples or SMS configuration strings from Aplicom, apply them in the order recommended by the manufacturer and keep placeholders such as APN values where required.

Configuration Notes​

  • Firmware differences can change menu locations and available fields in the Aplicom configuration tool; always note the firmware version before making changes.
  • When given a choice, UDP may be preferred for lower overhead and TCP when guaranteed delivery or session management is required; test both if unsure.
  • Plaspy uses port 8888 for all devices and automatically detects the incoming protocol to simplify server configuration.
  • Confirm APN and cellular registration prior to changing server settings to avoid false negatives during validation.
  • If you move the A9 Quick between vehicles, verify power and accessory connections such as the Aplicom 3PAD if used for driver reporting.

Why Use Plaspy with This Configuration​

Using the Aplicom A9 Quick with Plaspy gives organizations a straightforward way to gain visibility into mobile assets. The A9 Quick’s portable design and internal antennas make it suitable for temporary or multi-vehicle deployments, and configuring the unit to report to Plaspy provides operational monitoring, motion reporting, and location history within a single platform.

To learn more about Plaspy and how it works with supported trackers visit https://www.plaspy.com. For device specific configuration methods, firmware behavior, and the latest manufacturer details verify information on the Aplicom website https://www.aplicom.com/ as vendor guidance may change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy