Skip to main content

Aplicom - T10 Configuration

This page covers the public configuration context for using the Aplicom T10 tracker with Plaspy. It explains the shared server settings and the practical setup steps you will use on the device or in the vendor management tools so the T10 can send telemetry and location to the Plaspy platform for real time visibility and fleet management.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol. Exact manufacturer-side setup steps can vary depending on firmware level, hardware revision, installation type, and whether you use Aplicom Silver Cloud or local configuration tools. This guide focuses on the public settings and workflow required to point a T10 at Plaspy and validate connectivity.

Configuration Overview​

The goal of configuration is to prepare the Aplicom T10 to communicate reliably with Plaspy and appear as an active device in your account. You will set the server endpoint and transport, confirm network connectivity, and validate that Plaspy receives the tracker data.

  • Point the device to the Plaspy server endpoint so telemetry and GPS data are routed to Plaspy.
  • Choose the transport protocol (UDP or TCP) if required by the device and network.
  • Set the shared Plaspy port so the platform can accept data from the tracker.
  • Validate device connectivity and that the tracker appears in Plaspy after configuration.
  • Use Aplicom Silver Cloud or the manufacturer configuration tool to apply settings and manage firmware remotely.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol and all devices in Plaspy use the same port

Typical Requirements Before Setup​

  • Reliable power to the T10 unit and any required ignition or external power cutouts during configuration.
  • Network connectivity appropriate for your variant (T10G and similar variants may require a cellular SIM for 2G where applicable).
  • Access to Aplicom Silver Cloud or the official Aplicom configuration tool or service provided by your vendor.
  • Administrative access to your Plaspy account so you can confirm device appearance and telemetry ingestion.
  • Device firmware that supports remote configuration and the ability to change server and transport settings.
  • Basic device identifiers such as serial number or IMEI so you can match the physical unit to the Plaspy device entry.

How This Tracker Connects to Plaspy​

When configured, the Aplicom T10 sends location and telemetry data to the shared Plaspy server endpoint and port for processing and display in the platform. Plaspy receives the incoming data stream and automatically detects the protocol used by the tracker so no per-device protocol selection is required on the platform side.

  • The tracker is pointed at d.plaspy.com or 54.85.159.138 and uses port 8888 for outbound telemetry.
  • You may select UDP or TCP on the device if it requires a transport choice; Plaspy supports both.
  • Plaspy automatically detects the tracker protocol so the platform can parse incoming messages without per-device protocol mapping.
  • Once telemetry is received, Plaspy makes device position, alerts, and status available in the platform for monitoring and reporting.
  • Validating the device in Plaspy confirms that the tracker is successfully reporting to the shared server endpoint and port.

Common Configuration Workflow​

  1. Access the official Aplicom configuration method or management tool such as Aplicom Silver Cloud or the vendor provisioning interface.
  2. Locate the server or destination settings in the device configuration panel.
  3. Enter the Plaspy server address using either d.plaspy.com or the IP 54.85.159.138.
  4. Set the server port to 8888 to match Plaspy's shared port.
  5. Choose UDP or TCP on the device if the tracker requires you to select a transport protocol.
  6. Apply or save the configuration changes using the manufacturer tool.
  7. Restart or power-cycle the device if required by the device or management system.
  8. Validate that the device reports to Plaspy by checking your Plaspy account for device presence and incoming telemetry.

Example Configuration Commands​

The exact commands and syntax for configuring an Aplicom T10 vary by firmware and whether you use Aplicom Silver Cloud, a vendor provisioning tool, or local serial/USB configuration. Because manufacturer tools differ, refer to Aplicom documentation for the specific command set or management interface you will use. In many deployments you will:

  • Use Aplicom Silver Cloud to create or push a configuration profile that sets the server to d.plaspy.com and port 8888.
  • Or use the device configuration utility to enter the server name or IP 54.85.159.138 and port 8888, and select UDP or TCP as the transport.

If you have a specific command list from Aplicom or your vendor, paste the commands into your configuration tool in the order recommended by the manufacturer. For device-specific command syntax consult Aplicom support or the device manual.

Configuration Notes​

  • Firmware differences across T-Series and regional variants can change how server and transport settings are entered; always check the device firmware release notes.
  • For T10G and cellular capable variants, ensure SIM provisioning and a compatible mobile plan if the device uses 2G cellular networks.
  • Choosing TCP versus UDP may affect delivery guarantees and firewall requirements at the network edge; configure transport according to your connectivity conditions.
  • Aplicom Silver Cloud can simplify mass provisioning and remote updates but verify profiles include the Plaspy server (d.plaspy.com) and port 8888.
  • Confirm device identifiers such as IMEI or serial number before and after configuration to ensure the correct unit is being validated in Plaspy.

Why Use Plaspy with This Configuration​

Using the Aplicom T10 with Plaspy provides a practical path to centralized tracking, asset visibility, and telemetry aggregation. The T10's rugged design and remote management capabilities complement Plaspy's ability to ingest telemetry from many devices using a consistent server endpoint and port, enabling tasks such as real time location monitoring and operational reporting.

To learn more about Plaspy visit https://www.plaspy.com. For the most current device specific configuration steps, firmware behavior, and manufacturer instructions verify details on the Aplicom website https://www.aplicom.com/. Manufacturer specifications and setup methods can change over time so always confirm the latest guidance before applying configuration at scale.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy