Skip to main content

Aplicom - T10 G Configuration

This page covers the public configuration context for using the Aplicom T10 G with Plaspy. It consolidates the practical, platform-level settings and workflow guidance you need to point an Aplicom T10 G device at Plaspy for location and CAN bus telemetry visibility. Use this documentation to confirm which values Plaspy requires and how the general configuration process fits into typical provisioning and installation steps.

Plaspy uses shared server settings across supported trackers and automatically detects the tracker protocol, while exact manufacturer-side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools such as Aplicom Silver Cloud. Follow the steps below as a practical reference and always verify device-specific options using Aplicom manufacturer documentation.

Configuration Overview​

This configuration prepares the Aplicom T10 G to send its location and CAN-derived telemetry to Plaspy using the platform's shared endpoint and port. The goal is to ensure the device can reach Plaspy reliably, present the expected telemetry, and be visible within the Plaspy fleet management interface.

  • Point the device at the Plaspy server endpoint so telemetry is routed to your account.
  • Select the transport protocol supported by the device and allowed on your network.
  • Set the common Plaspy port and save the configuration on the device or provisioning tool.
  • Validate connectivity and device reporting to confirm Plaspy is receiving location and CAN signals.
  • Use manufacturer tools or Aplicom Silver Cloud for remote provisioning when available.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol

Typical Requirements Before Setup​

  • A powered and accessible Aplicom T10 G device with the desired firmware installed.
  • An active cellular configuration and SIM profile compatible with the device variant for LTE Cat M1 and 2G fallback as needed.
  • Access to the official Aplicom configuration tool or provisioning method for the T10 G, such as device management provided by Aplicom Silver Cloud or local configuration utilities.
  • Network access that allows outbound UDP or TCP to d.plaspy.com on port 8888 and any intermediate firewall rules adjusted accordingly.
  • Credentials or account access required by Aplicom device management if remote provisioning is used.
  • A plan to validate telemetry and CAN signals once the device is registered in Plaspy.

How This Tracker Connects to Plaspy​

The Aplicom T10 G sends location and CAN bus telemetry to Plaspy by directing its data stream to the platform's shared server endpoint and port. Plaspy listens on a single port for all supported devices and uses protocol detection to interpret incoming messages from the tracker.

  • The device is configured to report to d.plaspy.com (or the equivalent IP) on port 8888.
  • Transport can be UDP or TCP depending on device settings and network policies.
  • Plaspy automatically detects the tracker protocol and maps incoming telemetry into the platform.
  • Location, CAN-derived signals, and event messages are transmitted from the device to Plaspy for real-time dashboards and reporting.
  • Successful configuration makes the T10 G visible and manageable inside Plaspy once the device transmits valid telemetry.

Common Configuration Workflow​

  1. Access the official Aplicom configuration method or software for the T10 G, using Aplicom Silver Cloud or the manufacturer tool recommended for your firmware.
  2. Enter the Plaspy server address d.plaspy.com or the server IP 54.85.159.138 in the device server/host field.
  3. Set the device port to 8888 as required by Plaspy.
  4. Choose UDP or TCP if the device requires an explicit transport selection.
  5. Apply or save the configuration in the device tool or provisioning interface.
  6. Restart the device if the configuration tool or device documentation indicates a reboot is required.
  7. Validate that the device reports to Plaspy by checking device status and incoming telemetry in the Plaspy platform.

Example Configuration Commands​

The exact command syntax and configuration method for the T10 G depend on the Aplicom provisioning tool or firmware version. Aplicom typically provides device-specific configuration utilities and remote provisioning through Aplicom Silver Cloud, so follow the manufacturer instructions for command formats and API usage. If you use a local configuration interface or serial/USB tool, enter the Plaspy server d.plaspy.com or 54.85.159.138 and set the device port to 8888, selecting UDP or TCP as needed.

Configuration Notes​

  • Firmware versions and hardware revisions can change available configuration options; always check the Aplicom T10 G release notes when possible.
  • Choose UDP or TCP based on your network environment and firewall rules; UDP can be lighter weight while TCP may be preferred where reliability over lossy links matters.
  • Plaspy uses the same port for all supported devices and performs automatic protocol detection, which simplifies per-device port assignment.
  • Remote provisioning via Aplicom Silver Cloud can streamline deployments for fleets but may require additional account setup or permissions.
  • Validate device reporting in Plaspy after configuration; a successful connection is the primary confirmation that settings are correct.

Why Use Plaspy with This Configuration​

Using the Aplicom T10 G with Plaspy brings vehicle-level telemetry and reliable location reporting into a single fleet management view. The T10 G's CAN interface and rugged design combined with Plaspy's platform-level protocol handling make it straightforward to collect ignition state, diagnostics, and continuous location for operational monitoring, asset tracking, and analytics.

Learn more about Plaspy and how the platform manages device connections at https://www.plaspy.com. For the latest Aplicom T10 G device-specific configuration details, firmware notes, and provisioning instructions, verify the official documentation at https://www.aplicom.com/ as manufacturer procedures and firmware behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy