Skip to main content

Appello - 5P Configuration

This page documents the public configuration context for using the Appello 5P GPS tracker with the Plaspy platform. It describes the server settings Plaspy requires, the common SMS-based setup commands published for the 5P, and practical steps to prepare the device so it can report location and status to Plaspy for monitoring and fleet visibility.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol. Manufacturer-side setup steps can vary by firmware, hardware revision, installation type, and vendor tools. The Appello 5P uses a SIMCOM SIM800C GPRS module and a u-blox MAX-7 GPS/GLONASS receiver; the public configuration below reflects the available SMS commands and Plaspy server details required to integrate the device.

Configuration Overview​

The goal of configuring the Appello 5P for Plaspy is to point the tracker at Plaspy's servers, provide the correct APN and connectivity credentials, and verify that the tracker reports correctly so it becomes visible and manageable within Plaspy. The 5P commonly accepts SMS commands for core settings, and the steps below focus on practical, public configuration elements.

  • Set the mobile operator APN and optional username/password so the device can establish GPRS data.
  • Configure the device to report to Plaspy's server endpoint and port so location and status messages reach the platform.
  • Adjust reporting interval or heartbeat settings so the tracker transmits at an appropriate frequency for the use case.
  • Validate connectivity and data flow by confirming the device appears in Plaspy after configuration.
  • Use the manufacturer's published SMS commands or official configuration tool to apply settings reliably.

Plaspy Server Settings​

  • Server domain: d.plaspy.com
  • Server IP: 54.85.159.138
  • Port: 8888 — Plaspy uses the same port for all supported devices
  • Transport: the device may be configured to use UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol so the platform can accept data from compatible trackers without manual protocol selection

Typical Requirements Before Setup​

  • A charged and powered Appello 5P with working battery and phone connectivity
  • An active SIM card with voice/SMS/data capability and the correct operator APN for GPRS access
  • Access to the manufacturer's published configuration method (SMS commands or official setup tool) and the device password (the example public commands use the default password 00000)
  • Basic SMS capability on the phone used to send configuration messages to the tracker
  • Time to verify device visibility in Plaspy after configuration

How This Tracker Connects to Plaspy​

The Appello 5P sends position and device status over the mobile data network (GPRS) to the Plaspy server endpoint and port. Plaspy receives those reports, identifies the tracker protocol automatically, and makes the device visible in the platform for tracking, event alerts, and operational monitoring.

  • The device is pointed at the Plaspy server endpoint (IP or domain) and port so packets reach the platform.
  • Packets are sent over the chosen transport (UDP or TCP) to port 8888.
  • Plaspy automatically detects the tracker protocol and parses location and status messages.
  • Once reporting is successful, the tracker appears in Plaspy for live location and historical playback.
  • Periodic heartbeat or interval messages can be adjusted so the device reports with the required frequency.

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or software (SMS commands or vendor tool) for the Appello 5P.
  2. Set the operator APN so GPRS data can be established (use the APN placeholders if required).
  3. Enter the Plaspy server endpoint — either d.plaspy.com or the IP 54.85.159.138 — into the device configuration.
  4. Set the server port to 8888 (Plaspy uses the same port across devices).
  5. Choose UDP or TCP on the device if it requires a transport selection.
  6. Apply or save the configuration and restart the device if the manufacturer instructions recommend a restart.
  7. Validate that the device reports to Plaspy by checking device presence and recent position updates in the platform.

Example Configuration Commands​

The Appello 5P can be configured using SMS commands. The following public commands are the published sample SMS messages for initial setup. The example commands use the device default password 00000 as shown in the manufacturer's public guidance.

  • Set the operator APN ([apn] placeholder required; [apnu] and [apnp] are optional username and password placeholders):
00000,apn,[apn],[apnu],[apnp]

Explanation: replace [apn] with your carrier APN. If your carrier requires an APN username or password, include [apnu] and [apnp] respectively; omit those values if they are not required.

  • Set the GPRS server to the Plaspy server IP and port:
00000,ip,54.85.159.138,8888

Note: If the device firmware supports hostnames, you can point the server to d.plaspy.com instead of the IP. Use the manufacturer's syntax for hostname entries if available.

  • Set the device update interval to 30 seconds (sample interval command from published guidance):
00000,t030s***n

Preserve the command order when applying these SMS settings if recommended by the manufacturer. Keep the default device password 00000 unless you have previously changed it; if you change the password, use the updated password in subsequent SMS commands.

Configuration Notes​

  • Firmware versions and hardware revisions can slightly change SMS syntax or feature availability — confirm the exact SMS format in the manufacturer's documentation for your device firmware.
  • The Appello 5P supports SMS-based configuration in public guidance; use SMS only from a trusted phone and confirm the correct device password before sending commands.
  • Choose UDP or TCP according to installation needs; Plaspy supports both transports on port 8888 and will accept messages over either transport.
  • APN placeholders [apn], [apnu], and [apnp] represent your carrier APN, username, and password; leave username/password blank if not required.
  • All devices in Plaspy use the same server port (8888) and Plaspy auto-detects the protocol, so once the device can reach d.plaspy.com or 54.85.159.138 on that port, the platform should recognize the tracker.

Why Use Plaspy with This Configuration​

Configuring the Appello 5P to report to Plaspy provides a straightforward path to centralized visibility and operational monitoring. Organizations benefit from consistent server settings, automatic protocol detection, and a single port architecture that simplifies device onboarding and reduces per-device configuration complexity.

To learn more about Plaspy and how it supports device integrations like the Appello 5P, visit https://www.plaspy.com. For the latest device-specific setup details, firmware notes, and manufacturer commands, verify current information on the manufacturer's official site http://www.cnjeo.com/ since device behavior and configuration methods can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy