Skip to main content

Appello - GT07 Configuration

This page describes the public configuration context for using the Appello GT07 tracker with Plaspy. It focuses on the practical server settings, required preparation, and the SMS commands published for the GT07 so the device can report to Plaspy for real time motorcycle tracking. Use this guide as a practical reference for applying the public settings that Plaspy requires.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while manufacturer-side steps can vary by firmware, hardware revision, installation type, and vendor tools. The GT07 has public SMS based commands for basic setup such as APN, GPRS server, and periodic reporting; those commands are included below and should be adapted to your SIM and installation conditions.

Configuration Overview​

The goal of the configuration process is to prepare the GT07 to communicate reliably with the Plaspy platform so location and basic device events appear in Plaspy. The GT07 can be configured using the published SMS commands to set timezone, APN, GPRS server and reporting interval, and to verify device status.

  • Configure the device APN and data credentials so the tracker can use GPRS data.
  • Point the tracker to the Plaspy server endpoint and port so reports are delivered.
  • Set an appropriate periodic update interval to balance timeliness and data usage.
  • Verify device settings and operational status with the provided check commands.
  • Confirm the tracker appears in Plaspy after configuration and monitor initial packets.

Plaspy Server Settings​

Use the following public server settings when configuring the GT07 to report to Plaspy:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support: UDP or TCP may be used on port 8888
  • Plaspy automatically detects the tracker protocol and all devices in Plaspy use the same port

These values are the shared endpoint information Plaspy publishes for device integration. Configure the GT07 to send its GPRS reports to either the domain or the IP above on port 8888 and choose UDP or TCP if your device requires a transport selection.

Typical Requirements Before Setup​

  • A powered and accessible GT07 tracker installed or on the bench for SMS configuration.
  • A working SIM card with SMS capability and an active data plan that supports GPRS.
  • The correct APN settings for the mobile operator (APN username and password if required).
  • Access to the vendor provided configuration method such as SMS commands or a configuration tool.
  • Ability to receive and send SMS from the phone used for configuration.
  • Manufacturer documentation or release notes for the GT07 to confirm firmware specific behaviors.

How This Tracker Connects to Plaspy​

The GT07 is configured to report location and basic device status to the shared Plaspy server endpoint and port so the device becomes visible in the Plaspy platform. Plaspy receives the incoming packets and automatically determines the tracker protocol used by the device.

  • GT07 sends periodic GPRS reports to d.plaspy.com or 54.85.159.138 on port 8888.
  • Reports can be sent over UDP or TCP depending on configuration capability.
  • Plaspy automatically detects the tracker protocol to interpret incoming messages.
  • After the tracker is configured, the device status can be validated with check commands and observed in Plaspy.
  • Proper APN and data connectivity are required for continuous reporting to the platform.

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or software for the GT07, typically the published SMS command set.
  2. Ensure the SIM card is inserted and has an activated data plan and SMS service.
  3. Enter the Plaspy server endpoint by sending d.plaspy.com or the server IP 54.85.159.138 in the device server configuration step.
  4. Set port 8888 for GPRS reporting and choose UDP or TCP if the device requires transport selection.
  5. Configure APN and optional APN credentials for the mobile operator so the tracker can open a GPRS session.
  6. Apply or save the configuration and restart the device if required or recommended by the manufacturer.
  7. Validate that the device reports to Plaspy by using the GT07 verification commands and checking for the device in Plaspy.

Example Configuration Commands​

The GT07 supports SMS based configuration. The following public commands are the documented sequence for setting common parameters. Preserve placeholders when replacing with your operator values.

  • Optional initial factory reset (use only if required for a fresh configuration)
940#
  • Set the time zone to UTC-0
801#W0#
  • Set the operator APN
802#[apn]#[apnu]#[apnp]#

Explanation: Replace [apn] with the mobile operator APN. If your operator requires an APN username or password, replace [apnu] and [apnp] with those values. If username and password are not required, some devices accept the APN alone.

  • Set the GPRS server to Plaspy (server IP and port)
803#54.85.159.138#8888#

Note: You may use the domain d.plaspy.com in the device configuration if the tracker firmware accepts a domain name instead of an IP.

  • Set the periodic update interval to 60 seconds
730#60#
  • Check current device settings
886#
  • Check device status
902#

Follow the commands in order when required by your setup; factory reset is optional and only recommended when a clean configuration state is needed.

Configuration Notes​

  • Manufacturer firmware and command syntax can vary by hardware revision and region; always verify the exact command set for your GT07 revision.
  • The GT07 supports SMS based setup as shown; some installers prefer USB or a configuration tool when available from the vendor.
  • Choose UDP or TCP according to the device firmware options and network conditions; both transports are supported by Plaspy on port 8888.
  • Plaspy uses the same port for all supported devices and automatically detects the tracker protocol for incoming connections.
  • Keep APN placeholders in commands when documenting configuration steps and replace them with operator specific values during setup.

Why Use Plaspy with This Configuration​

Using the GT07 with Plaspy provides a straightforward path to motorcycle visibility and basic operational monitoring. By pointing the device to Plaspy's shared server endpoint and using the published SMS commands to configure APN, server, and reporting interval, organizations can bring GT07 telemetry into the Plaspy platform for location tracking and status checks.

Learn more about Plaspy on the main website https://www.plaspy.com and verify the latest device specific setup details and firmware behavior with the manufacturer at http://www.cnjeo.com/. Manufacturer specifications and setup methods can change over time so confirm current instructions on the official vendor site.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy