Skip to main content

ArkNav - CT-X8 Configuration

This page covers the public configuration context for using the ArkNav CT-X8 Container Lock GPS Tracker with Plaspy. It explains the shared Plaspy server settings you need to apply to the device so the CT-X8 can send telemetry and tamper events to Plaspy for centralized monitoring and alerts. Use this guide as a practical reference alongside ArkNav documentation for device-specific steps.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, and Plaspy also uses the same port for all devices. Exact manufacturer-side setup steps can vary by firmware version, hardware revision, installation style, and the vendor configuration tools you use. Always confirm device-specific details in the official ArkNav documentation when preparing installations.

Configuration Overview​

This configuration process prepares the CT-X8 to report GPS positions, intrusion events, and telemetry to the Plaspy platform so operators gain timely visibility and event history. The objective is to point the device at Plaspy's server endpoint, confirm transport settings, and verify the tracker appears in your Plaspy account.

  • Set the device server address to Plaspy so position and event data are routed into the platform.
  • Select the transport method supported by your tracker firmware and save the network settings.
  • Configure reporting intervals to match operational needs and battery management profiles.
  • Validate connectivity so the unit appears in Plaspy and begins sending location and tamper events.
  • Confirm event reporting such as door open detection is active so alerts are delivered to Plaspy.

Plaspy Server Settings​

When configuring the CT-X8 for Plaspy, use the following public server settings exactly as shown:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol and uses the same port for all supported devices

These values are the public Plaspy endpoint information that ArkNav devices should be pointed at during configuration.

Typical Requirements Before Setup​

  • A CT-X8 unit with required accessories such as the USB to serial programming cable if using local configuration tools
  • A charged 3.7 V backup battery or external power as required for initial configuration and testing
  • A working SIM card and cellular connectivity provisioned for data and SMS if the device is to use GSM communications
  • Access to the official ArkNav configuration tool or documentation for device-specific setup steps
  • A Plaspy account or access to the Plaspy platform so you can validate device reporting and visibility
  • Basic means to receive SMS or serial responses if the tracker uses SMS or USB serial for configuration feedback

How This Tracker Connects to Plaspy​

The CT-X8 transmits GPS positions and tamper events over cellular to the shared Plaspy server endpoint and port, where Plaspy ingests and normalizes the telemetry and event data. Once connected, Plaspy displays live positions, stores historical routes, and triggers configured alerts or workflows.

  • The unit reports GPS location fixes and intrusion or door open events to d.plaspy.com or 54.85.159.138 on port 8888
  • The device can use UDP or TCP as the transport depending on firmware and the installer selection
  • Plaspy automatically detects the tracker protocol so devices using different protocols can share the same server and port
  • Incoming telemetry is presented in Plaspy dashboards, event feeds, and alerting systems for operational monitoring
  • Successful reporting confirms the tracker is visible in Plaspy and that real time and historical data are available

Common Configuration Workflow​

  1. Access the official ArkNav configuration method or software using the manufacturer tool, USB to serial cable, or approved vendor interface.
  2. Enter the Plaspy server domain d.plaspy.com or, where a numeric address is required, enter 54.85.159.138.
  3. Set the server port to 8888 as the destination port for telemetry and event reporting.
  4. Choose UDP or TCP if the device requires a transport selection; pick the transport supported by your firmware and network conditions.
  5. Configure reporting intervals and event reporting options to match your operational profile and battery strategy.
  6. Apply or save the configuration in the device tool and follow any device prompts to commit settings.
  7. Restart the device if required by the ArkNav procedure to ensure settings take effect.
  8. Validate that the device reports to Plaspy by checking device visibility and recent telemetry inside your Plaspy account.

Example Configuration Commands​

The exact configuration commands depend on the ArkNav firmware and the configuration interface you use (for example manufacturer software, USB serial console, or SMS). Because commands vary by firmware and toolchain, the recommended approach is to use ArkNav's official configuration utility or the documented SMS/serial command set from the manufacturer. Typical actions you will perform with those tools include pointing the server to d.plaspy.com or 54.85.159.138 and setting port 8888 along with transport selection.

If you have ArkNav provided command strings or an SMS command set from the device manual, apply them in the sequence ArkNav documents and preserve any placeholders the manufacturer provides when entering APN or credentials. For example, if a manufacturer SMS template uses placeholders such as [apn], [apnu], or [apnp], keep those placeholders and replace them with your carrier APN settings when instructed by ArkNav documentation.

Configuration Notes​

  • Firmware versions and hardware revisions can change available configuration menus and command formats; always match commands to the device firmware.
  • Choose UDP or TCP based on network reliability and ArkNav guidance; both transports are supported by Plaspy on port 8888.
  • SMS based provisioning and USB to serial programming are commonly used for CT-X8 setup; follow ArkNav instructions for either method.
  • Plaspy uses the same port for all supported devices and auto detects the tracker protocol, so you do not need a different port per device.
  • Keep a copy of your final configuration and test telemetry delivery to Plaspy before deploying devices in the field.

Why Use Plaspy with This Configuration​

Using the ArkNav CT-X8 with Plaspy gives operations centralized visibility of container locations and tamper events so teams can respond quickly to incidents and maintain chain of custody records. The CT-X8's rugged design and configurable reporting profiles make it suitable for port and intermodal use while Plaspy provides the dashboards, alerts, and historical reporting needed for operational oversight.

To learn more about Plaspy and how it integrates with compatible trackers visit https://www.plaspy.com. For the latest device specific configuration commands, firmware notes, and installation guidance verify details on the manufacturer site https://www.arknavgps.com.tw/ since setup methods and firmware behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy