Skip to main content

ArkNav - RX-9 3G Configuration

This page provides the public configuration context for using the ArkNav RX-9 3G vehicle tracker with Plaspy. It explains the shared Plaspy server settings you will apply to the device, outlines typical prerequisites, and describes the practical workflow to prepare the RX-9 3G for visibility in the Plaspy platform. The RX-9 3G is a waterproof vehicle tracker with built in GPS and GSM modules and features such as temperature sensing, driver ID support, and configurable tracking behavior that make it suitable for fleet management and asset tracking.

Plaspy uses a shared server endpoint and the same port for all supported devices and automatically detects the tracker protocol when the device connects. Exact manufacturer-side setup steps for the RX-9 3G can vary by firmware version, hardware revision, installation type, or vendor configuration tools. Use this guide as a practical public reference for the Plaspy settings and workflow, and cross check final actions with ArkNav documentation or the configuration tool you are given.

Configuration Overview​

Configuring the RX-9 3G for Plaspy focuses on directing the tracker to the Plaspy server and ensuring the device can open a transport session (UDP or TCP) to send its reports. Once the tracker connects to the shared Plaspy endpoint on the required port, Plaspy will detect the protocol and begin ingesting location and event data for visibility in the platform.

  • Point the tracker to the Plaspy server endpoint so outbound telemetry reaches the platform
  • Choose the transport mode supported by the device and the network, UDP or TCP
  • Verify cellular connectivity, SIM and APN settings if required by your installation
  • Save and apply settings, then restart the tracker if the device requires it
  • Confirm the device is reporting and visible in Plaspy after configuration

Plaspy Server Settings​

When configuring the ArkNav RX-9 3G for Plaspy, use the following public server settings exactly as shown:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol when the device connects

Note that Plaspy uses the same port across all supported devices and will detect the correct protocol automatically once the device establishes a connection.

Typical Requirements Before Setup​

  • Access to the ArkNav official configuration method or software provided by the manufacturer or vendor
  • Device powered with sufficient battery or external power and installed according to manufacturer instructions
  • Active cellular SIM and data connectivity configured if the device requires a SIM for GPRS
  • APN and related SIM credentials ready if required by your SIM provider
  • Knowledge of the device IMEI or unique identifier for registration or verification in Plaspy
  • Access to Plaspy account or platform user to confirm device visibility after setup
  • Manufacturer documentation or support contact to resolve firmware or hardware specific differences

How This Tracker Connects to Plaspy​

The RX-9 3G sends its position and event data over the cellular network to the shared Plaspy server endpoint and port. Once configured to point at the Plaspy endpoint, the tracker opens a UDP or TCP session and transmits location updates, heartbeats, and event messages which Plaspy processes and displays.

  • The tracker initiates an outbound connection to d.plaspy.com or to 54.85.159.138 on port 8888
  • Data transport can use either UDP or TCP depending on device settings and network conditions
  • Plaspy automatically detects the tracker protocol and begins decoding incoming messages
  • Location updates, alarm events, and sensor readings from the RX-9 3G are forwarded to Plaspy for live monitoring
  • After successful connection the device becomes visible and manageable in Plaspy for tracking and reporting

Common Configuration Workflow​

  1. Access the ArkNav RX-9 3G official configuration method, tool, or software provided by the manufacturer or your vendor.
  2. Enter the Plaspy server address by configuring d.plaspy.com or the server IP 54.85.159.138 in the device server settings.
  3. Set the server port to 8888 as the destination port for telemetry.
  4. If the device requires a transport selection, choose UDP or TCP based on your network and device preferences.
  5. Enter any required SIM APN and credentials if the tracker needs cellular data to reach Plaspy.
  6. Apply or save the configuration and restart the tracker if the device firmware requires a reboot for changes to take effect.
  7. Validate that the device successfully reports to Plaspy by checking device visibility and recent position updates in your Plaspy account.

Example Configuration Commands​

The ArkNav RX-9 3G may be configured using manufacturer tools, SMS commands, or over the air firmware utilities depending on firmware and vendor setup. Exact commands depend on the ArkNav configuration syntax and firmware version and are not provided here as part of this public guide.

Refer to the ArkNav user manual or your vendor tool for the specific command format required to set the server domain, server IP, port, transport type, and APN. If you have a set of manufacturer commands, apply them in the order required by the device and include placeholders such as [apn] or [apnu] exactly as provided by the manufacturer; these placeholders should be replaced with your SIM APN, username, and password when required.

Configuration Notes​

  • Firmware differences can change command syntax and available options; always confirm the correct commands for your device firmware.
  • TCP and UDP offer different behaviors on variable networks; choose the transport that matches your network reliability and device support.
  • The RX-9 3G supports OTA firmware updates according to ArkNav documentation; some configuration options may be added or modified via firmware updates.
  • Built in antennas and waterproof enclosure affect installation choices; follow ArkNav guidance for optimal placement and cable routing.
  • Keep a record of the device IMEI and configuration applied to simplify registration and troubleshooting with Plaspy and ArkNav support.

Why Use Plaspy with This Configuration​

Using the ArkNav RX-9 3G with Plaspy provides organizations with a straightforward way to collect vehicle location, event alerts, and sensor readings in a unified platform. Directing the tracker to the shared Plaspy endpoint on port 8888 enables consistent ingestion of telemetry across a mixed fleet, while Plaspy’s automatic protocol detection removes the need to manually select or register low level protocol variants.

To learn more about Plaspy and how it can integrate with trackers like the ArkNav RX-9 3G visit https://www.plaspy.com. For the latest ArkNav device specific setup details, firmware notes, and configuration tools verify information on the manufacturer site https://www.arknavgps.com.tw/. Manufacturer specifications and setup methods can change over time so always cross check with ArkNav documentation when applying configuration changes.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy