Skip to main content

ATrack - AK7S Configuration

This page covers the public configuration context for using the ATrack AK7S tracker with the Plaspy platform. It focuses on the practical server settings and example device commands that are commonly used to connect an AK7S to Plaspy, and how to validate that the device is reporting successfully.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while exact manufacturer side setup steps can vary by firmware, hardware revision, installation type, and vendor configuration tools. Where available this page includes example AT$ commands from public AK7S configuration content and explains placeholders such as APN and APN credentials.

Configuration Overview​

This configuration prepares the AK7S to send location and event data to Plaspy and to be visible on the platform. The goal is to set device reporting rules, apply a GPRS server endpoint that points to Plaspy, and verify the device is connected and reporting.

  • Configure device event reporting and tracking interval so the AK7S transmits useful telemetry to Plaspy.
  • Set the device form and data mode to match Plaspy expectations so packets are parsed correctly.
  • Apply GPRS server settings that point to Plaspy so the tracker opens a data session to the monitoring host.
  • Validate connectivity and status using the device status query so you can confirm registration on Plaspy.
  • Ensure APN and SIM data plan are correct so the tracker can create a mobile data connection.

Plaspy Server Settings​

  • Server domain d.plaspy.com for device reporting and platform ingestion
  • Server IP 54.85.159.138 as the public endpoint for devices
  • Port 8888 which Plaspy uses for all supported devices
  • Transport support for UDP or TCP; the device may be configured to use either protocol on port 8888
  • Plaspy automatically detects the tracker protocol when data arrives

Typical Requirements Before Setup​

  • A working SIM card with a mobile data plan and correct APN settings for the deployed mobile operator
  • Power to the AK7S and access to the device configuration interface or the official ATrack configuration tool
  • Manufacturer documentation or a configuration channel that allows sending the AK7S AT$ commands shown below
  • Confirmation of the device firmware revision if possible, since command availability and behavior can change with firmware
  • Access to Plaspy account or administrator view so you can confirm the device appears after configuration

How This Tracker Connects to Plaspy​

The AK7S is configured to open a GPRS data session and send binary or protocol-formatted packets to the Plaspy server endpoint and port. Plaspy uses the shared server endpoint and port to receive data and determine the tracker protocol automatically.

  • The device transmits location and event records to d.plaspy.com or directly to 54.85.159.138 on port 8888
  • Plaspy inspects incoming connections and data to detect the correct tracker protocol automatically
  • Event rules configured on the AK7S (for example ACC events) are sent to Plaspy for alerting and monitoring
  • Regular tracking intervals keep location visibility current in the platform once reporting is active
  • Transport choice (UDP or TCP) is set on the device but Plaspy accepts either on the same port

Common Configuration Workflow​

  1. Access the official ATrack configuration method or software that supports sending AK7S AT$ commands.
  2. Enter the Plaspy server information by specifying d.plaspy.com or the server IP 54.85.159.138.
  3. Set the port to 8888 which Plaspy uses for all supported devices.
  4. Choose UDP or TCP as the transport on the device if a transport selection is required.
  5. Configure event reporting and tracking parameters such as ACC events and reporting interval.
  6. Apply or save the configuration and restart the device if the tool or firmware requires a reboot.
  7. Validate the device reports to Plaspy by checking device status and confirming presence in the Plaspy platform.

Example Configuration Commands​

The following example commands are derived from public AK7S configuration content. They show a typical sequence and must be adapted to your operator APN values and your configuration method. Preserve placeholders and replace them with your operator values.

  • Set ACC event reporting and actions
AT$INPT=0,7
AT$REPT=101,1,"%IN0","1",0,1
AT$REPT=102,1,"%IN0","0",0,1
AT$RACT=1,3,2
  • Set tracking interval to 60 seconds
AT$TRAC=1,60,,,,,2
  • Set the device to binary mode (protocol form)
AT$FORM=1,@P,0,""
  • Configure GPRS server with APN placeholders and Plaspy server IP and port
AT$GPRS=1,"[apn]","[apnu]","[apnp]","54.85.159.138",8888,1,3,30,0,0

Explanation of placeholders:

  • [apn] is the mobile operator APN name

  • [apnu] is the APN username if required by the operator; leave empty if not needed

  • [apnp] is the APN password if required by the operator; leave empty if not needed

  • Check device status

AT$INFO=?

Note: Replace placeholders with your real APN, APN username, and APN password values before saving.

Configuration Notes​

  • The commands above are illustrative and reflect a common public configuration pattern for the AK7S; command availability may vary by firmware.
  • Choose UDP or TCP according to installation needs; Plaspy accepts either on the shared port 8888 and will detect the protocol automatically.
  • Keep APN and credentials confidential and confirm them with your mobile operator if data sessions do not establish.
  • If you use a manufacturer configuration tool, prefer that tool for bulk or remote provisioning where possible.
  • Validate configuration after reboot by issuing AT$INFO=? or checking the Plaspy platform for the device heartbeat.

Why Use Plaspy with This Configuration​

Using the ATrack AK7S with Plaspy gives organizations a straightforward way to centralize vehicle location, event alerts, and operational oversight. Pointing the AK7S to Plaspy using the shared server settings and standard reporting commands allows the platform to receive and interpret tracker data reliably.

To learn more about deploying Plaspy for fleet tracking visit https://www.plaspy.com. For the most current device specific setup instructions, firmware notes, and technical documentation for the AK7S please verify details on the manufacturer site https://www.atrack.com.tw/ as setup methods and firmware behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy