AutoFon - α-Маяк Configuration
This page describes the public configuration context for using the AutoFon α-Маяк with the Plaspy platform. It summarizes the shared Plaspy server settings you will point the tracker to, explains the practical steps to prepare the device for reporting, and highlights what to check before and after integration. The information here focuses on publicly available setup guidance and the common workflow used to enable device visibility in Plaspy.
Plaspy uses a shared server endpoint and the same port for all supported devices and automatically detects the tracker protocol when a device connects. Exact manufacturer side setup steps for the AutoFon α-Маяк can vary by firmware version, hardware revision, installation method, and vendor configuration tools, so use this page as a practical reference and confirm device specific details with the official AutoFon documentation.
Configuration Overview
The goal of configuring an AutoFon α-Маяк for Plaspy is to direct the tracker to the Plaspy server endpoint, ensure reliable GSM connectivity, and validate that periodic and event driven reports arrive in the platform. This allows objects tracked by the α-Маяк to appear in Plaspy for monitoring and historical location review.
- Point the device to the Plaspy server domain or IP and set the shared port used by Plaspy
- Choose the transport protocol if the device requires UDP or TCP selection
- Apply and save the manufacturer configuration so the tracker sends data to Plaspy
- Verify connectivity and that the device is visible in the Plaspy platform
- Optionally adjust reporting frequency or activation behavior in the device management tools
Plaspy Server Settings
Configure the tracker to report to Plaspy using these public settings:
- Server domain d.plaspy.com
- Server IP 54.85.159.138
- Port 8888
- Transport support for UDP or TCP on port 8888
- Plaspy automatically detects the tracker protocol when the device connects
Note that Plaspy uses the same port 8888 for all devices supported by the platform.
Typical Requirements Before Setup
- Confirm the AutoFon α-Маяк is powered and operational and its battery pack is installed
- Ensure the device has GSM network coverage consistent with its operation over the GSM network
- Have access to the official AutoFon configuration method or software provided by the vendor
- Know the device identity information or registration details used by the manufacturer portal
- Be prepared to select transport type UDP or TCP if the device firmware requires a manual choice
- Have the ability to save settings and restart the tracker if the change requires a reboot
How This Tracker Connects to Plaspy
The AutoFon α-Маяк transmits location and event data via the GSM network to the shared Plaspy server endpoint. In practice, you configure the device to use the Plaspy server domain or IP and port 8888, then verify the device begins reporting. Plaspy will accept either UDP or TCP connections and will identify the device protocol automatically.
- Device sends periodic location reports to d.plaspy.com or 54.85.159.138 on port 8888
- Transport can be configured as UDP or TCP depending on device settings
- Plaspy automatically detects the tracker protocol and processes incoming data
- Reports become visible in Plaspy for real time monitoring and historical review
- Event driven messages such as forced activation or SOS can be delivered to the same server endpoint
Common Configuration Workflow
- Access the official manufacturer configuration method or software for the AutoFon α-Маяк
- Enter the Plaspy server domain d.plaspy.com or the server IP 54.85.159.138 in the server address field
- Set the server port to 8888 as required by Plaspy
- Choose UDP or TCP if the device requires transport selection
- Apply or save the configuration in the manufacturer tool or device settings
- Restart the device if the configuration tool or firmware indicates a reboot is required
- Validate that the device reports to Plaspy by checking for the tracker in the platform and confirming incoming messages
Example Configuration Commands
The exact commands or configuration strings used to program the AutoFon α-Маяк depend on the manufacturer tool, firmware revision, and the provisioning method provided by AutoFon. AutoFon devices are often configured through the vendor software or a configuration utility rather than a single universal command string, so refer to the official AutoFon configuration guide for command level details when needed.
Configuration Notes
- Firmware differences and hardware revisions may change how settings are entered or saved; always check the device firmware version before applying instructions
- If the device firmware offers both UDP and TCP options choose the transport that matches your operational requirements; Plaspy accepts either and auto detects the protocol
- Plaspy uses the same port 8888 for all supported devices which simplifies server configuration across a mixed device fleet
- Adjust reporting frequency and activation behavior through the AutoFon management tools or the device Personal Area when those features are available
- Manufacturer documentation is the primary source for any command line or SMS based configuration methods
Why Use Plaspy with This Configuration
Using the AutoFon α-Маяк with Plaspy gives organizations a straightforward way to collect location data on a reliable shared endpoint. Because the α-Маяк is designed for long battery life and automatic operation, integrating it with Plaspy provides a low maintenance tracking solution for asset visibility and event monitoring.
To learn more about Plaspy and platform capabilities visit https://www.plaspy.com. For the most current device specific configuration details, firmware updates, and manufacturer guidance refer to the official AutoFon website https://www.autofon.ru/ as manufacturer specifications and setup methods can change over time.
Tracker Configuration
Need a platform for this tracker setup
Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.