Skip to main content

AutoFon - D-Маяк МОТО Configuration

This page documents the public configuration context for using the AutoFon D‑Маяк МОТО tracker with Plaspy. It focuses on the practical server and setup information you will need to point the tracker at Plaspy for GPRS tracking and SMS fallback. Use this guidance together with the device manufacturer documentation to complete the setup for your installation.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while exact manufacturer side setup steps can vary by firmware, hardware revision, installation type, and vendor tools. The D‑Маяк МОТО supports GPRS packet reporting and SMS control as noted in the device description, so the common workflow is to configure the device to report to the Plaspy endpoint and verify it appears in your Plaspy monitoring account.

Configuration Overview​

The goal of configuration is to prepare the D‑Маяк МОТО to communicate reliably with the Plaspy monitoring server so that location, event alerts, and diagnostic telemetry are delivered in real time. The tracker’s internal buffering and resend logic will help preserve packets during temporary connectivity loss, but a correct server configuration is required for continuous visibility.

  • Point the tracker to the Plaspy monitoring endpoint so GPRS packets are sent to the correct server.
  • Configure the transport and port as required by the device firmware, using UDP or TCP on the Plaspy port.
  • Provide or verify SIM and APN settings so the device can establish a GPRS data session.
  • Save and apply the device configuration then restart if required so the new server values take effect.
  • Validate connectivity in Plaspy and confirm event and telemetry messages are received.
  • Remember that Plaspy uses the same port for all supported devices and automatically detects the tracker protocol.

Plaspy Server Settings​

Use the following public Plaspy server settings when configuring the D‑Маяк МОТО for GPRS reporting:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support using UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol so devices can use either UDP or TCP and be recognized by the platform

All Plaspy devices report to the same port and Plaspy will determine the protocol automatically.

Typical Requirements Before Setup​

  • A charged and installed SIM card with a mobile data plan enabled for GPRS packet transfer and an APN value ready to configure if required.
  • Access to the official AutoFon configuration method or software for the D‑Маяк МОТО (manufacturer tool, SMS command set, or configuration utility).
  • The device must have power applied and be reachable for configuration and testing.
  • Knowledge of the device APN credentials and any required owner or admin PINs used by the tracker.
  • A Plaspy account and access to your Plaspy project so you can confirm device registration and incoming telemetry.
  • Optional access to SMS command capability as a fallback if configuring via a software tool is not possible.

How This Tracker Connects to Plaspy​

When configured for GPRS reporting, the D‑Маяк МОТО sends its location and telemetry packets to the Plaspy server endpoint and port where Plaspy ingests the data, applies protocol parsing, and displays events in the platform. SMS remains available as a fallback control channel for certain commands if GPRS is unavailable.

  • The tracker is configured to report to the shared Plaspy server endpoint (d.plaspy.com or 54.85.159.138) on port 8888.
  • Plaspy receives GPRS packets and automatically detects the device protocol for parsing and display.
  • Location updates and accelerometer events from the device are forwarded into Plaspy as position and event records.
  • Alarm input, auxiliary channel status, battery and power reports are visible in Plaspy dashboards and event streams.
  • Device black box buffering and resend logic will forward stored packets to the Plaspy server when connectivity is restored.

Common Configuration Workflow​

  1. Access the official AutoFon configuration method or software for the D‑Маяк МОТО (manufacturer app, desktop tool, or SMS command interface).
  2. Enter the Plaspy server address using either the domain d.plaspy.com or the server IP 54.85.159.138 as required by the configuration tool.
  3. Set the server port to 8888 as the destination port for GPRS packet reporting.
  4. Choose UDP or TCP if the device requires a transport selection; Plaspy supports both and will auto detect the protocol.
  5. Enter APN and SIM related settings if required so the device can establish a GPRS session.
  6. Apply or save the configuration and perform a device restart if the device or tool requires one.
  7. Validate that the device reports to Plaspy by checking the Plaspy project for incoming positions and events.

Example Configuration Commands​

There are no manufacturer commands included on this public page. Exact commands and the method to send them depend on the AutoFon D‑Маяк МОТО firmware and the configuration tool provided by AutoFon. Common manufacturer methods include:

  • Using AutoFon configuration software or a web interface when available.
  • Sending SMS configuration commands if the device supports SMS-based setup.

Refer to the official AutoFon configuration guide for the precise command syntax or utilities required to set the server, port, transport, and APN values for your device.

Configuration Notes​

  • Firmware and hardware revisions can change command syntax and configuration menus; always consult the device release notes when available.
  • Choose UDP or TCP according to the device options; Plaspy accepts both and will detect the protocol automatically once packets arrive on port 8888.
  • The D‑Маяк МОТО supports SMS control as a fallback, which can be useful for remote verification or when GPRS is temporarily unavailable.
  • Confirm APN, APN user, and APN password values with the SIM provider before provisioning the device.
  • Remember that Plaspy uses the same port for all supported devices which simplifies server configuration across mixed fleets.

Why Use Plaspy with This Configuration​

Using the AutoFon D‑Маяк МОТО with Plaspy gives organizations reliable remote visibility for motorcycles and exposed assets while leveraging the device’s long battery life, sensor suite, and internal black box storage. When pointed at the Plaspy server endpoint and port, the tracker’s location and event packets are parsed and presented in real time, enabling monitoring, alerting, and historical reporting for operational oversight and security workflows.

To learn more about Plaspy and how to manage devices at scale visit https://www.plaspy.com. For the latest device specific configuration methods, firmware behavior, and manufacturer details verify the official AutoFon documentation at https://www.autofon.ru/ as implementations and command sets can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy