Skip to main content

AutoFon - Омега-Маяк XL Configuration

This page documents the public configuration context for using the AutoFon Омега-Маяк XL tracker with Plaspy. It focuses on the practical server settings and workflow needed to point the device at Plaspy so the tracker can deliver location and event data to the monitoring platform. The content here uses publicly available Plaspy server details and general guidance compatible with the tracker description.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol; however, exact manufacturer-side setup steps can vary by firmware version, hardware revision, installation type, and the vendor configuration tools you use. Refer to the official AutoFon configuration methods for device-specific commands, and use the Plaspy server settings below when you configure the tracker to report to Plaspy.

Configuration Overview​

This configuration prepares the Омега-Маяк XL to send its location and status to Plaspy using the device GPRS reporting capability or other manufacturer supported channels. The goal is to configure the tracker to communicate reliably with the Plaspy monitoring endpoint so that position updates, alerts, and stored packets are visible in the platform.

  • Set the device monitoring server to the Plaspy endpoint so GPRS packets are directed to the platform.
  • Confirm transport and port settings so the tracker can establish a session with Plaspy.
  • Validate network connectivity and data reporting from the device to ensure packets arrive.
  • Verify visibility of the device inside Plaspy after configuration and initial reporting.
  • Keep manufacturer tools or SMS commands available for adjustments and firmware related changes.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP; configure UDP or TCP on the device if required
  • Plaspy automatically detects the tracker protocol so the same port is used for all supported devices

Note that Plaspy uses the same port for all devices and relies on automatic protocol detection to interpret incoming tracker traffic.

Typical Requirements Before Setup​

  • A charged or powered tracker with access to the configuration interface such as the device micro USB configuration tool or the manufacturer configuration method
  • At least one active SIM card with a data plan and GPRS access if you will use mobile data reporting
  • Network coverage for the SIM operator in the device location
  • Access to the official AutoFon configuration documentation or vendor software to make server and transport changes
  • The device firmware version and hardware revision noted so you can follow the correct manufacturer instructions
  • Optional: the ability to receive or send SMS commands if your configuration method uses SMS

How This Tracker Connects to Plaspy​

The Омега-Маяк XL reports position and event information to the monitoring server selected in its GPRS configuration. When configured to use Plaspy, the tracker delivers packets to the Plaspy endpoint so the platform can display location and status.

  • The tracker sends GPRS packets to the configured monitoring server address and port
  • Set the device to use either UDP or TCP transport as required by the tracker configuration interface
  • Packets directed to d.plaspy.com or 54.85.159.138 on port 8888 arrive at Plaspy where the protocol is detected automatically
  • Plaspy ingests the data and makes the device visible in the monitoring platform for tracking and event reporting
  • After initial reporting, validate that updates and stored black box packets appear in Plaspy

Common Configuration Workflow​

  1. Access the official AutoFon configuration method or software for the Омега-Маяк XL (for example manufacturer PC tool, USB configuration utility, or supported SMS command set).
  2. In the server or monitoring settings, enter d.plaspy.com or the Plaspy server IP 54.85.159.138 as the destination.
  3. Set the device port to 8888, matching the Plaspy listening port used for all devices.
  4. If the device requires a transport selection, choose UDP or TCP according to device capability or your network preference.
  5. Apply or save the configuration in the manufacturer tool or send the configuration SMS commands if using SMS setup.
  6. Restart the tracker if the device or manual recommends a restart to apply the new server settings.
  7. Validate that the device reports to Plaspy by checking for incoming positions and events in the monitoring platform.

Example Configuration Commands​

The exact commands and syntax for configuring the Омега-Маяк XL vary by manufacturer firmware and the configuration method you use. AutoFon devices commonly offer PC tools, USB utilities, and SMS command sets for server and APN configuration. Because model firmware differs, follow the official AutoFon command list or configuration tool for precise commands.

If your vendor supplies SMS commands or a configuration utility, typical actions you will perform include setting the APN values (if required), specifying the monitoring server as d.plaspy.com or 54.85.159.138, and setting the reporting port to 8888. Preserve any placeholders the manufacturer uses for APN values such as [apn], [apnu], or [apnp] when applying commands, and consult AutoFon documentation for exact syntax.

Configuration Notes​

  • Firmware variations can change command syntax and available options; confirm the exact commands with AutoFon documentation.
  • The Омега-Маяк XL supports reporting via GPRS to a monitoring server; ensure your SIM supports GPRS data.
  • Two SIM cards are supported on this device family; make sure the active SIM for data is the one configured to use the Plaspy server.
  • Choose UDP or TCP based on device capability and network reliability; Plaspy accepts either transport on port 8888.
  • Keep device black box packet behavior and storage considerations in mind if using offline buffering or batch uploads.

Why Use Plaspy with This Configuration​

Configuring the Омега-Маяк XL to report to Plaspy provides a straightforward path to monitor positions, events, and stored packets from the device in a single platform. Using the shared Plaspy server endpoint simplifies deployment across multiple trackers because the platform automatically detects device protocols and uses a single listening port for all supported devices.

To learn more about Plaspy and platform features, visit https://www.plaspy.com. For the most current device specific commands, firmware notes, and configuration tools consult the manufacturer at https://www.autofon.ru/ so you can confirm the latest setup details and command syntax.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy