Skip to main content

AutoFon - SE+ Маяк Configuration

This page documents the public configuration context for using the AutoFon SE+ Маяк tracker with Plaspy. It collects the practical, platform-oriented steps and settings you will need to point the device at Plaspy so the tracker can deliver location and event data to the monitoring platform. The content here focuses on publicly available setup information and how the device typically communicates to a monitoring server.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when the device connects. Exact manufacturer side setup steps can vary depending on firmware version, hardware revision, installation type, and the configuration tool you use. Where the device supports both SMS and GPRS reporting, SMS is often useful for initial configuration or simple alerts, while GPRS is the usual channel for continuous reporting to Plaspy.

Configuration Overview​

This guide helps you prepare an AutoFon SE+ Маяк device to send its location and event data to Plaspy using the platform shared server endpoint and port. The goal is to configure the tracker to establish a reliable GPRS connection to Plaspy, confirm transport and reporting behavior, and verify visibility in the Plaspy platform.

  • Point the tracker to the Plaspy server endpoint so it will send GPRS packets to the monitoring platform.
  • Configure the device transport to use UDP or TCP on the shared Plaspy port.
  • Ensure the tracker has a working SIM card and valid APN so it can connect via GPRS.
  • Validate the device reports after configuration so the tracker appears in Plaspy.
  • Use SMS based commands if required by the manufacturer for initial configuration or troubleshooting.

Plaspy Server Settings​

Use these public Plaspy settings when configuring your AutoFon SE+ Маяк:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support is available for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol when the device connects and uses the same port for all supported devices

Typical Requirements Before Setup​

  • A powered AutoFon SE+ Маяк unit installed or temporarily connected for configuration
  • A valid SIM card with active GPRS data or the ability to receive SMS for command based setup
  • APN details for the SIM provider if GPRS is required by the device
  • Access to the official AutoFon configuration method or software for this model such as SMS command set or manufacturer tool
  • A Plaspy account or access to your Plaspy administrator so you can confirm the device appears in the platform after configuration

How This Tracker Connects to Plaspy​

The AutoFon SE+ Маяк can transmit coordinates and event data to a monitoring server using GPRS. For Plaspy integration you configure the device to send its packets to the shared Plaspy server endpoint and port so the platform can receive and interpret the tracker data.

  • The tracker is configured to report to the Plaspy server endpoint d.plaspy.com or directly to 54.85.159.138
  • All data is sent to the shared port 8888 which Plaspy uses for supported devices
  • You may select UDP or TCP transport on the tracker if the device requires a transport selection
  • Plaspy automatically detects the tracker protocol on connection so no special protocol selection is needed in Plaspy
  • As the device supports SMS reporting, SMS can be used for configuration or emergency messages while GPRS provides continuous reporting to Plaspy

Common Configuration Workflow​

  1. Access the official AutoFon configuration method for the SE+ Маяк such as the documented SMS commands, the manufacturer configuration utility, or technician tool.
  2. Enter the Plaspy server address using either the domain d.plaspy.com or the server IP 54.85.159.138 depending on the device option.
  3. Set the destination port to 8888 in the device server settings.
  4. Choose the transport method UDP or TCP if the device requires explicit transport selection.
  5. Supply APN and any SIM provider credentials required for GPRS so the device can open a data session.
  6. Apply or save the configuration on the device and restart the tracker if the manufacturer recommends a reboot.
  7. Validate that the device reports to Plaspy by checking for the tracker in your Plaspy account or by confirming received packets on the platform.

Example Configuration Commands​

The exact commands and syntax for configuring an AutoFon SE+ Маяк vary by firmware and the manufacturer SMS command set or configuration tool. Because model specific commands are provided by AutoFon in their official documentation, use the method recommended by the manufacturer for your firmware revision. Common manufacturer methods include:

  • SMS based commands to set server and port
  • A PC or mobile configuration utility supplied by the manufacturer
  • Direct configuration by a service technician using the device interface

If you have the official AutoFon SMS command set or configuration script from the manufacturer, follow the documented order of commands and preserve any placeholders for APN or credentials exactly as provided by AutoFon.

Configuration Notes​

  • Firmware differences can change the exact SMS syntax or configuration UI. Always check the device firmware version before applying commands.
  • Choosing UDP or TCP on the tracker affects transport reliability and firewall traversal. Test both transports if connectivity issues occur.
  • Use SMS configuration only when GPRS is not yet available or for troubleshooting initial connectivity.
  • Provide correct APN settings for the SIM operator so the device can establish a GPRS session.
  • AutoFon supports remote firmware updates via GPRS so it is a good practice to verify firmware level and update if necessary before wide deployment.

Why Use Plaspy with This Configuration​

Using Plaspy with the AutoFon SE+ Маяк provides a straightforward way to centralize location and event telemetry from the tracker into a single monitoring platform. With the tracker pointed at the Plaspy shared server endpoint and port, organizations gain visibility into movement, alerts, and device status using the platform tools they already rely on.

To learn more about Plaspy visit https://www.plaspy.com and review the official AutoFon documentation at https://www.autofon.ru/ to verify the latest model specific configuration steps and firmware behavior.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy