Skip to main content

Autoseeker - AT-07 Configuration

This page covers the public configuration context for using the Autoseeker AT-07 GPS mini tracker with Plaspy. It summarizes the practical settings you will apply on the device or via manufacturer tools so the AT-07 can report location and status to the Plaspy platform. Use this page as a focused integration guide and reference the manufacturer materials for device-specific interfaces.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, so the server endpoint and port are the same for all devices. Exact manufacturer-side setup steps can vary by firmware version, hardware revision, installation type, and vendor configuration tools; follow the official Autoseeker instructions for the exact command syntax or UI flow when required.

Configuration Overview​

Prepare the AT-07 to communicate reliably with Plaspy by setting the device server endpoint, transport, and any required network parameters. The goal is to ensure the device can establish a connection and that Plaspy can automatically identify the device protocol and start receiving updates.

  • Set the tracker to report to the Plaspy server endpoint and port used by all Plaspy devices.
  • Choose the transport method supported by the tracker (UDP or TCP) if the device requires selection.
  • Save and apply the configuration through the official Autoseeker configuration tool or command interface.
  • Validate that the AT-07 is visible and reporting in Plaspy after configuration.
  • Troubleshoot connectivity by checking device power, network coverage, and that the device accepted the new server settings.

Plaspy Server Settings​

Use the following public Plaspy server settings when configuring the Autoseeker AT-07:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol for incoming connections

These settings are the same across all devices supported by Plaspy and enable the platform to receive and identify device traffic consistently.

Typical Requirements Before Setup​

  • Confirm the AT-07 is powered, has sufficient battery, and is operational.
  • Have physical access to the device or access to the manufacturer configuration method or software.
  • A Plaspy account or administrator access to the Plaspy platform to verify device reporting.
  • Network connectivity appropriate to the device so it can reach external servers.
  • The Autoseeker user manual or configuration reference for your firmware version.
  • Basic troubleshooting tools such as a serial cable, USB adapter, or the vendor's configuration app when applicable.

How This Tracker Connects to Plaspy​

When configured for Plaspy, the AT-07 sends its location and status updates to the shared platform endpoint so the device becomes visible in Plaspy for monitoring and event reporting. Plaspy uses the same port for all devices and automatically detects the tracker protocol to process incoming messages correctly.

  • The tracker is set to report to the Plaspy server endpoint d.plaspy.com (or the equivalent IP).
  • Messages are sent over the configured transport on port 8888.
  • Plaspy inspects incoming data and automatically detects the tracker protocol.
  • Once connected, the device will appear in Plaspy for real-time location and status monitoring.
  • Regular reporting and event messages allow operational monitoring and alerts within Plaspy.

Common Configuration Workflow​

  1. Access the official Autoseeker configuration method or software for the AT-07 (manufacturer app, SMS commands if supported, or a desktop utility).
  2. Enter the Plaspy server domain d.plaspy.com or the server IP 54.85.159.138 in the device server field.
  3. Set the device port to 8888.
  4. Choose UDP or TCP transport if the device requires selecting a transport protocol.
  5. Apply or save the configuration through the device interface or send the configuration commands.
  6. Restart the AT-07 if the manufacturer instructions require a reboot for settings to take effect.
  7. Validate that the device reports to Plaspy and appears in the platform; confirm connectivity and data flow.

Example Configuration Commands​

The exact commands and syntax for the AT-07 depend on the Autoseeker configuration method and firmware version. Manufacturers commonly provide a command list, an SMS command set, or a configuration application. When using command-based setup, the typical public actions are to set server domain or IP, set port, and set transport. For example, a command sequence (illustrative only) would set server and port then save:

  • Set server to domain or IP 
    set server d.plaspy.com
    or 
    set server 54.85.159.138
  • Set port 
    set port 8888
  • Set transport if required 
    set transport udp
    or 
    set transport tcp
  • Save and restart if the tool requires it 
    save
    restart

Note: The exact command names and syntax vary by firmware and manufacturer tool. Preserve any placeholders provided by the Autoseeker documentation such as [apn] or [apnu] when those values are part of the official command set. Consult the Autoseeker manual for precise commands for your device and firmware.

Configuration Notes​

  • Firmware variations can alter command syntax and available configuration options; check the AT-07 documentation for your firmware.
  • Some vendor tools present graphical settings rather than raw commands; the same Plaspy server domain or IP and port values are required regardless of the interface.
  • When given the option, UDP is commonly used for tracker reporting but select the transport that matches your network and the manufacturer recommendation.
  • Plaspy uses the same port for all supported devices and will automatically detect the tracker protocol, reducing the need to select a protocol on the server side.
  • Market or regional device variants may require slightly different configuration steps; verify with Autoseeker documentation.

Why Use Plaspy with This Configuration​

Using the Autoseeker AT-07 with Plaspy provides a straightforward server configuration that enables the device to report location and status to a single, shared endpoint. This simplifies fleet or asset onboarding because the same server settings (d.plaspy.com, 54.85.159.138, port 8888) apply across devices and Plaspy will automatically detect the tracker protocol to process incoming messages.

If you want to learn more about Plaspy and how it can manage tracking data from devices like the Autoseeker AT-07 visit https://www.plaspy.com. For the most current device-specific configuration commands, firmware notes, and manufacturer details always verify the latest information on the official Autoseeker website https://autoseekergps.com/ .

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy