Skip to main content

Autoseeker - AT-17C Configuration

This page provides public configuration context for using the Autoseeker AT-17C asset tracker with Plaspy. It focuses on the shared server settings and practical setup considerations required to point the device at Plaspy so the platform can receive location and alarm data from the unit.

Plaspy uses a shared server endpoint and the same listening port for all supported devices and automatically detects the tracker protocol when data arrives. Manufacturer-side setup steps for the AT-17C can vary by firmware version, hardware revision, installation type, and the vendor configuration tools you use; follow the vendor documentation alongside these Plaspy-specific settings.

Configuration Overview​

Preparing the AT-17C for Plaspy mainly means configuring the tracker to report its telemetry to Plaspy's ingestion endpoint and verifying connectivity. The following items describe the practical goals of the configuration process.

  • Point the device to Plaspy's public server endpoint so telemetry is routed to your Plaspy account.
  • Configure the transport layer and port used by the tracker so it can communicate with Plaspy.
  • Verify cellular connectivity and reporting mode so the device can send GPRS TCP or SMS reports as supported.
  • Validate that position, alarm and tamper events are visible in Plaspy after the device comes online.
  • Save and apply the configuration on the tracker and, if required, restart the device to begin reporting.

Plaspy Server Settings​

Use these public Plaspy settings when configuring the AT-17C. Plaspy requires the same port for all devices and automatically detects the protocol used by the tracker.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol when data arrives

Typical Requirements Before Setup​

  • A charged AT-17C unit with sufficient battery or temporary power for initial configuration and testing.
  • An active SIM card with a data plan and SMS ability if you will use GPRS TCP reporting or SMS reporting.
  • Access to the official Autoseeker configuration method or software for your device firmware revision.
  • Knowledge of the device APN and any SIM credentials required by your mobile operator.
  • A Plaspy account or platform access where you can confirm that the device appears and reports.
  • A test environment or temporary installation location with cellular coverage to validate reporting.

How This Tracker Connects to Plaspy​

When configured for Plaspy, the AT-17C sends location and alarm data to Plaspy's shared ingestion endpoint and port. Plaspy receives the inbound telemetry, detects the device protocol automatically, and surfaces positions, alarms, and history in the platform.

  • The tracker is pointed to d.plaspy.com or the fallback IP 54.85.159.138 so telemetry is routed to Plaspy.
  • Data is sent on port 8888, which Plaspy uses for all device connections.
  • The device can report over GPRS TCP or via SMS depending on configuration and network availability.
  • Plaspy automatically detects the tracker protocol and maps incoming messages to the device record.
  • Once the device reports, Plaspy will show live positions, tamper alerts, and scheduled reports per the device settings.

Common Configuration Workflow​

  1. Access the official Autoseeker configuration method or vendor software for the AT-17C for your firmware and hardware revision.
  2. In the device server or APN settings, enter the Plaspy server domain d.plaspy.com or use the server IP 54.85.159.138 if your tool requires an IP.
  3. Set the port to 8888 as Plaspy uses the same port across all devices.
  4. Choose the transport protocol UDP or TCP if the tracker requires an explicit transport selection.
  5. Enter APN or SIM operator credentials if required by your carrier, then apply or save the configuration.
  6. Restart the device if the manufacturer recommends a reboot to apply new network settings.
  7. Validate that the AT-17C reports to Plaspy by checking your Plaspy account for live position, telemetry, or alarm events.

Example Configuration Commands​

The AT-17C supports reporting over GPRS TCP and SMS, but specific configuration commands and formats vary by firmware and the Autoseeker configuration tool you use. Because manufacturer tools and SMS command formats change, follow the official Autoseeker configuration guide for exact commands.

In practice, configuration actions you will perform using vendor tools or SMS typically include specifying:

  • the server as d.plaspy.com or 54.85.159.138,
  • the port as 8888,
  • the transport as UDP or TCP,
  • and APN credentials for the installed SIM if required.

If you are using an SMS-based setup method, the vendor manual will provide the exact SMS command syntax and placeholders you may need to substitute for APN or phone numbers.

Configuration Notes​

  • Firmware and hardware revisions may change available configuration fields and SMS command formats; always confirm the correct procedure for your unit.
  • Choose TCP when persistent, ordered delivery of GPRS telemetry is preferred; UDP can be used where supported and if lower overhead is desired.
  • SMS reporting can be used as a fallback or for remote queries when data connectivity is limited.
  • Ensure the SIM APN and carrier settings are correct before concluding a configuration session.
  • After applying settings, allow time for the device to register on the cellular network and begin reporting to Plaspy on port 8888.

Why Use Plaspy with This Configuration​

Using the Autoseeker AT-17C with Plaspy provides low-maintenance, long-life asset visibility and integrated alarm reporting for fleet and asset management. Pointing the tracker at Plaspy's shared server endpoint lets the platform automatically detect device protocol and ingest telemetry for real-time monitoring, historical reports, and tamper alert workflows.

To learn more about Plaspy and how it consolidates location and alarm data for fleet and asset operations visit https://www.plaspy.com. For the latest device specific setup steps, SMS command formats, and firmware notes for the AT-17C consult the official Autoseeker documentation at https://autoseekergps.com/ since manufacturer procedures and firmware behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy