Skip to main content

Autoseeker - AT-17K Configuration

This page provides the public configuration context for connecting the Autoseeker AT-17K 4G Solar Wireless Magnetic GPS Tracker to Plaspy. It focuses on the shared server settings Plaspy requires and practical steps commonly used to prepare the AT-17K for reporting location and telemetry into the Plaspy platform. Use this as a practical reference for setup planning and verification.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, but exact manufacturer-side steps can vary by firmware version, hardware revision, installation type, and vendor tools. The AT-17K is documented here as a Plaspy compatible device that streams location and status over cellular networks; always reconcile these public steps with the official Autoseeker documentation and your current firmware.

Configuration Overview​

Preparing the AT-17K for Plaspy involves configuring its uplink endpoint, verifying cellular connectivity, and confirming the device reports the expected telemetry to Plaspy. The goal is to make the tracker visible in the Plaspy dashboard so you can use real-time location, history playback, and event alerts.

  • Point the tracker to the Plaspy server endpoint and ensure transport settings match the device configuration options.
  • Confirm SIM and cellular connectivity so the tracker can send location and alarm data over 4G LTE or GSM.
  • Validate battery and solar recharge operation so the device remains online for the intended deployment duration.
  • Test alarm and telemetry reporting such as low battery, vibration, and tamper events so Plaspy can trigger workflows.
  • Verify the device appears in Plaspy and that location updates and historical tracks are visible.

Plaspy Server Settings​

When configuring the AT-17K for Plaspy, the following public server settings are used. Plaspy uses the same port for all supported devices and automatically detects the tracker protocol.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP; the device may be configured using UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol so the platform interprets the incoming data stream

Typical Requirements Before Setup​

  • A powered AT-17K with sufficient battery charge and, if possible, solar exposure for field testing.
  • A working cellular SIM card active on 4G LTE or GSM networks appropriate for your region.
  • Access to the official Autoseeker configuration method or software used for the AT-17K (SMS commands, web tool, or USB/serial tool depending on the vendor toolchain).
  • Confirmed APN and cellular credentials for the SIM in use if your region or operator requires them.
  • A stable place to test the device outdoors with clear view of the sky to obtain GPS fixes and complete initial reporting.
  • Administrative access to your Plaspy account or the person who will register and monitor the device in Plaspy.

How This Tracker Connects to Plaspy​

The AT-17K sends GPS position and onboard telemetry over the cellular network to the Plaspy server endpoint and port. Plaspy ingests those messages, automatically recognizes the protocol, and exposes location, history, and event data in the platform for monitoring and reporting.

  • The tracker is configured to report to the shared Plaspy server endpoint d.plaspy.com or 54.85.159.138.
  • Data is sent on port 8888 using either UDP or TCP depending on the device transport configuration.
  • Plaspy automatically detects the protocol and parses the incoming telemetry for map display and event rules.
  • Telemetry commonly reported includes position updates, battery and solar status, and alarm events such as vibration or tamper alerts as supported by the AT-17K.
  • Successful configuration results in the device appearing in Plaspy with live updates and historical route playback.

Common Configuration Workflow​

Follow this practical sequence when preparing an AT-17K for Plaspy. Exact steps can vary by firmware and the Autoseeker configuration tool you use.

  1. Access the official Autoseeker configuration method or vendor software for the AT-17K (SMS commands, configuration app, or configuration cable and PC tool).
  2. Enter the Plaspy server address by specifying either d.plaspy.com or 54.85.159.138 in the device server or host field.
  3. Set the device port to 8888 as required by Plaspy.
  4. Choose UDP or TCP if the device requires explicit transport selection; the AT-17K may be configured to use either on port 8888.
  5. Enter any required APN or carrier credentials for your SIM so the tracker can obtain a data connection.
  6. Apply or save the configuration in the Autoseeker tool and, if the device requires it, restart the device to activate the new settings.
  7. Validate that the device reports to Plaspy by checking for incoming location updates and telemetry in the Plaspy platform.

Example Configuration Commands​

The exact configuration commands and interface depend on the Autoseeker firmware and the vendor tools you use. Manufacturers sometimes provide SMS command sets, a PC configuration tool, or a mobile app for this model. Because commands vary by firmware, refer to the official Autoseeker configuration guide for the AT-17K for the precise syntax and sequence.

If you have specific public Autoseeker commands from your device firmware or vendor, include them here when following manufacturer guidance and preserve any placeholders such as APN values or usernames exactly as provided.

Configuration Notes​

  • Firmware and hardware revisions can change available settings and command formats; always verify the command syntax against your device firmware version.
  • If the device offers both UDP and TCP transports, test both if you encounter connectivity issues; Plaspy will accept either on port 8888 and will detect the tracker protocol automatically.
  • Ensure the SIM APN is correct for your cellular operator; missing or incorrect APN is the most common cause of failed uplinks.
  • For deployments relying on long battery life and solar recharge, validate power telemetry reporting so you can monitor battery health in Plaspy.
  • Keep a copy of any SMS or configuration steps used to program the device so installations can be replicated across multiple units.

Why Use Plaspy with This Configuration​

Using the Autoseeker AT-17K with Plaspy gives organizations a straightforward path to continuous visibility and operational monitoring for assets in harsh environments. The AT-17K’s extended battery life and solar recharge combined with Plaspy’s unified ingestion and automatic protocol detection make it practical to manage long-term deployments with fewer manual interventions.

To learn more about Plaspy and how it supports fleet and asset tracking, visit https://www.plaspy.com. For the most current device specific configuration methods, firmware details, and official commands for the AT-17K, please verify information with the manufacturer at https://autoseekergps.com/ as device behavior and setup instructions can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy