Skip to main content

GlobalSat - TR-616C1 Configuration

This page documents the public configuration context for using the GlobalSat TR-616C1 tracker with Plaspy. It focuses on the practical settings and commands that you can use to point a TR-616C1 at the Plaspy server so the device reports positions and events to your Plaspy account. Content here is derived from public configuration examples and the model configuration snippet provided with this tracker.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while the exact manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools. The TR-616C1 supports TCP UDP and SMS reporting and provides remote configuration options that are commonly used to register the device with Plaspy.

Configuration Overview​

This configuration process prepares the TR-616C1 to communicate reliably with the Plaspy platform so you can monitor vehicles and assets in real time. The key objective is to set the device network parameters and reporting endpoint so that position and event data are routed to Plaspy on the standard Plaspy port.

  • Configure APN and network access so the tracker can connect over cellular data
  • Set the Plaspy server endpoint and port so the device sends telemetry to Plaspy
  • Choose UDP or TCP transport when required by the tracker firmware
  • Validate device connectivity and confirm the device appears online in Plaspy
  • Optionally use SMS commands for remote setup where IP access is not available

Plaspy Server Settings​

Use the following public server settings when configuring the TR-616C1 for Plaspy integration. Plaspy uses the same port for all supported devices and automatically detects the tracker protocol.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol so the platform accepts a variety of tracker report formats

Typical Requirements Before Setup​

  • A powered and accessible TR-616C1 installed in the vehicle or bench powered for configuration
  • Active cellular SIM with data enabled and correct APN settings for the mobile network
  • Device IMEI available for use in SMS or manufacturer tools when addressing a specific unit
  • Access to the official GlobalSat configuration method such as SMS commands or vendor configuration software
  • Basic knowledge of whether you will use UDP or TCP transport for reporting
  • Network coverage at the device location to allow immediate validation of the connection

How This Tracker Connects to Plaspy​

The TR-616C1 reports GPS positions, events, and telemetry to the Plaspy endpoint using the configured transport and port. Plaspy receives the inbound messages, automatically identifies the tracker protocol, and maps incoming data into the platform for visibility and alerts.

  • The tracker is configured to report to the shared Plaspy server endpoint and port
  • Messages are sent over TCP or UDP to port 8888 depending on device transport settings
  • Plaspy stores real time positions and also processes buffered uploads when connectivity resumes
  • Events such as ignition state, motion triggers, and power loss are reported to Plaspy for alerts
  • After configuration the device should become visible in Plaspy and begin regular reporting

Common Configuration Workflow​

  1. Access the official GlobalSat configuration method or vendor software or prepare to send SMS commands according to the manufacturer guidance
  2. Enter the Plaspy server hostname or IP address using d.plaspy.com or 54.85.159.138 as the server endpoint
  3. Set the server port to 8888 which is the standard Plaspy port used by all devices
  4. Choose UDP or TCP transport if the device requires a transport selection
  5. Configure APN, APN username, and APN password if the device uses cellular data
  6. Apply or save the configuration on the device and execute any required commit command
  7. Restart or reboot the device if required to activate settings
  8. Validate that the device reports to Plaspy and appears online in the platform

Example Configuration Commands​

The TR-616C1 can be configured via SMS commands. The model configuration example uses SMS commands with placeholders. Preserve the placeholders when building your SMS messages.

Note about format used by Plaspy

  • The configuration example references a Plaspy message format example TSPRXAB27GHKLMnaicz*U!

Setup command

  • Replace the placeholders before sending
  • [imei] is the device IMEI
  • [apn] is the APN for your cellular provider
  • [apnu] is the APN username if required
  • [apnp] is the APN password if required
  • [checksum] must be computed as the XOR checksum of the command string before the asterisk in uppercase hexadecimal two digit format

Example SMS setup command

GSS,[imei],3,0,D1=[apn],D2=[apnu],D3=[apnp],E0=54.85.159.138,E1=8888,A1=1*[checksum]!

Reboot command

  • Optional reboot to apply settings immediately
  • [checksumreeboot] is the checksum for the reboot command string

Example SMS reboot command

GSC,[imei],3,0,LH*[checksumreeboot]!

Checksum explanation

  • The checksum in these commands is commonly calculated by XORing each character code of the command substring that appears before the asterisk, then converting the result to a two digit uppercase hexadecimal string. The example web snippet provided in the original configuration uses this XOR method.

Configuration Notes​

  • The TR-616C1 supports SMS based configuration as shown above and also supports remote configuration over data if vendor software is available
  • Transport choice TCP versus UDP depends on your installation preferences and firmware options; Plaspy accepts both on port 8888
  • Always verify APN settings with the mobile operator and use the correct APN credentials in D1 D2 D3 placeholders
  • Firmware revisions and vendor tools can change exact command syntax or available fields so confirm with the latest GlobalSat documentation when needed
  • If you use the IP address 54.85.159.138 or the domain d.plaspy.com both point to the Plaspy endpoint and are acceptable in device configuration

Why Use Plaspy with This Configuration​

Using the GlobalSat TR-616C1 with Plaspy gives fleet and asset managers a straightforward path to real time tracking, event alerts, and historical playback. The TR-616C1 s multi band cellular support and buffered logging help maintain continuity of tracking while Plaspy handles incoming messages, protocol detection, and platform level visibility.

To learn more about Plaspy visit https://www.plaspy.com and review additional platform capabilities. For the latest device specific configuration methods firmware notes and manufacturer guidance verify the current documentation on the GlobalSat website https://www.globalsat.com.tw/

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy