Skip to main content

GOTOP - D10 Configuration

This page provides the public configuration context for using the GOTOP D10 tracker with Plaspy. It collects the practical, platform-facing settings and workflow guidance needed to point a D10 device at Plaspy so the device can send location, alarm, and basic telemetry data into the Plaspy platform.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when data arrives. Manufacturer side setup steps can vary by firmware, hardware revision, installation type, and vendor tools, so use this page for Plaspy-focused settings and follow GOTOP documentation for device-specific configuration tools and procedures.

Configuration Overview​

Configuring the D10 for Plaspy ensures the tracker can reach the Plaspy ingest endpoint and be visible in your Plaspy account. The goal is to provide the device with the correct server endpoint, transport, and any network prerequisites so that location and event packets arrive reliably.

  • Set the device to report to Plaspy using the shared server endpoint and port so Plaspy can receive and normalize telemetry.
  • Verify cellular connectivity and APN settings on the D10 so data packets can be delivered to Plaspy.
  • Choose the transport type supported by the device and point it at the Plaspy server so automatic protocol detection can map incoming packets.
  • Validate reporting by checking that location, alarm, and power state messages appear in Plaspy.
  • Save and apply configuration changes and, if required by firmware, restart the device to begin reporting.

Plaspy Server Settings​

Use the following Plaspy server values when configuring the D10. Plaspy uses the same port for all supported devices and automatically detects the tracker protocol.

  • Server domain: d.plaspy.com
  • Server IP: 54.85.159.138
  • Port: 8888
  • Transport: UDP or TCP supported; choose the transport your device firmware requires
  • Note: Plaspy automatically detects the tracker protocol after the device sends data to the server endpoint

Typical Requirements Before Setup​

  • Confirm the D10 is powered and accessible for configuration or temporary direct connection.
  • Install a working Micro SIM card with active data service and correct APN settings for the local mobile network.
  • Have the device IMEI and any vendor-provided configuration tool, SMS command list, or USB/serial software ready.
  • Ensure you have a Plaspy account or administrator access to verify the tracker appears and sends telemetry.
  • Review the GOTOP user manual or vendor interface for the exact configuration method supported by your D10 firmware.
  • If installed covertly, plan a safe method to reboot the device or apply settings without disrupting operation.

How This Tracker Connects to Plaspy​

When configured, the D10 sends its location, alarms, and status reports to the Plaspy endpoint so operators can monitor devices centrally. Point the D10 to the Plaspy server and port, and Plaspy will detect the protocol and process incoming packets into device events and location history.

  • The D10 transmits location fixes and hybrid positioning data to d.plaspy.com or 54.85.159.138 on port 8888.
  • Alarms such as vibration, geofence, ignition state, and power events are forwarded to Plaspy for alerting and workflows.
  • Battery and power-failure messages allow Plaspy to present device health indicators and trigger maintenance notifications.
  • Plaspy normalizes incoming packets and automatically detects the device protocol so minimal manual mapping is required on the platform side.
  • When applicable, optional features like SOS or immobilizer events are reported so Plaspy can include them in operator alerts.

Common Configuration Workflow​

  1. Access the official GOTOP configuration method or software for the D10 as described in the manufacturer's documentation.
  2. In the device server settings, enter d.plaspy.com or the Plaspy server IP 54.85.159.138 as the primary reporting endpoint.
  3. Set the device port to 8888 to match Plaspy's ingest port used for all supported devices.
  4. If the device requires selecting a transport, choose UDP or TCP according to the D10 firmware option.
  5. Apply or save the configuration in the device interface or via the vendor tool.
  6. Restart the D10 if the firmware requires a reboot for network settings to take effect.
  7. Validate the device reports to Plaspy by confirming incoming telemetry and location updates in your Plaspy account.

Example Configuration Commands​

The D10 can be configured using the manufacturer tools, SMS commands, or configuration software depending on firmware and vendor distributions. Exact commands and syntax vary by firmware version and the vendor tool you use, so consult the GOTOP documentation for precise command formats.

If your device uses SMS configuration commands provided by GOTOP, follow the manufacturer command list and substitute the Plaspy server domain or IP and port as shown in the Common Configuration Workflow. Plaspy will accept data on d.plaspy.com or 54.85.159.138 using port 8888 and detect the protocol automatically.

Configuration Notes​

  • Firmware differences can change the exact configuration fields, command syntax, and available transports; always check the D10 firmware release notes.
  • The D10 supports dual server IP configuration in many firmware variants; you can configure a secondary backend for redundancy while using Plaspy as the primary endpoint.
  • Choose UDP or TCP based on device firmware support and network conditions; UDP is common for low overhead telemetry while TCP can be used where guaranteed delivery is needed and supported.
  • Verify APN and SIM data service are functional before validating reporting to the Plaspy endpoint.
  • Keep the GOTOP manual and firmware changelog handy because manufacturer configuration steps and available commands may be updated.

Why Use Plaspy with This Configuration​

Using the GOTOP D10 with Plaspy provides centralized visibility into real-time location, alarms, and device health for small vehicles and portable assets. The D10's hybrid positioning and alarm features deliver the event data Plaspy needs to populate dashboards, trigger alerts, and support operational workflows across mixed fleets.

To learn more about Plaspy visit https://www.plaspy.com. For the latest device specific configuration methods firmware behavior and manufacturer details please verify current information on the GOTOP website https://www.gotop.cc/

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy