Skip to main content

GOTOP - G01 Configuration

This page covers the public configuration context for using the GOTOP G01 tracker with the Plaspy platform. It collects the practical, public-facing server settings and workflow guidance needed to point a G01 device at Plaspy and validate reporting without replacing the official manufacturer documentation.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, but exact manufacturer-side setup steps can vary by firmware, hardware revision, installation type, and vendor tools. Use the instructions here to prepare the device for Plaspy ingestion and always confirm device-specific commands and procedures with the official GOTOP materials.

Configuration Overview​

This configuration prepares the G01 to send location and vehicle telemetry to Plaspy so devices become visible in the platform for live monitoring, alerts and reporting.

  • Point the G01 to Plaspy's shared server endpoint and port so the device can establish reporting to the platform.
  • Configure transport settings (UDP or TCP) on the device if required; Plaspy supports both and will auto-detect the tracker protocol.
  • Validate connectivity and telemetry by confirming the device appears in Plaspy and sends expected events such as ACC, SOS or power status.
  • Save and apply configuration on the tracker and, if needed, restart the unit to begin fresh reporting sessions.
  • Use the official GOTOP configuration method or a supported vendor tool to avoid firmware-specific pitfalls.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP; configure the tracker for either transport if the device requires a selection
  • Plaspy automatically detects the tracker protocol when the device connects
  • Note that all devices in Plaspy use the same port for device reporting

Typical Requirements Before Setup​

  • Physical access to the G01 unit and a safe location to apply or change settings
  • A valid SIM card installed with data or SMS enabled as required by the device's manufacturer configuration
  • Access to the official GOTOP configuration method such as the vendor software, SMS command set, or serial/UART interface depending on the device packaging
  • Sufficient battery or vehicle power applied so the device can complete configuration and connect to the network
  • A Plaspy account or deployment prepared to receive and validate device connections
  • Basic knowledge of selecting UDP or TCP on the device if transport selection is required

How This Tracker Connects to Plaspy​

When configured, the G01 streams GNSS positions and vehicle telemetry over GSM to the Plaspy ingestion endpoint so fleet managers get live updates and alerts in Plaspy dashboards.

  • The tracker is configured to report to the shared Plaspy server endpoint (d.plaspy.com or 54.85.159.138) using port 8888
  • Transport can be UDP or TCP depending on the device configuration; Plaspy supports both and will auto-detect the protocol
  • Location fixes, ACC status, SOS, power loss and other supported inputs are forwarded to Plaspy for mapping and alerting
  • Plaspy ingests the incoming device messages and makes them available for real-time monitoring, history and event workflows

Common Configuration Workflow​

  1. Access the official GOTOP configuration method or software recommended for the G01 (SMS commands, vendor tool, or serial/UART interface).
  2. Enter the Plaspy server domain d.plaspy.com or the server IP 54.85.159.138 in the device server/center settings.
  3. Set the device reporting port to 8888, which is the shared Plaspy port for all devices.
  4. Choose UDP or TCP on the tracker if the device requires a transport selection.
  5. Apply or save the configuration using the manufacturer tool or command set.
  6. Restart the device if required by the device firmware or vendor guidance to begin a fresh registration.
  7. Validate that the device reports to Plaspy by checking the Plaspy platform for incoming messages or device status updates.

Example Configuration Commands​

The exact command set for configuring a GOTOP G01 depends on the firmware and the manufacturer-provided interface. Because manufacturer commands vary, this page does not include device-specific SMS or serial commands. Use the GOTOP configuration guide or vendor software to perform the server, port and transport changes listed above.

If you have a device command reference from the manufacturer, apply the public Plaspy values when setting the server and port:

  • Server: d.plaspy.com or 54.85.159.138
  • Port: 8888
  • Transport: UDP or TCP (as required)

Preserve any placeholders in manufacturer examples (for example an APN placeholder such as [apn]) and replace them with your SIM provider details when instructed by GOTOP documentation.

Configuration Notes​

  • Behavior and the exact configuration commands may differ between G01 firmware revisions and hardware batches; check GOTOP documentation for firmware-specific syntax.
  • TCP vs UDP: choose the transport required by your installer tool or network environment; Plaspy supports both and will auto-detect the protocol on connection.
  • All Plaspy devices use the same port (8888) so multiple device types share the same platform entry point.
  • If using SMS-based configuration or a serial/UART interface, follow manufacturer timing and command formatting to avoid partial writes.
  • Keep a record of applied settings and firmware version when deploying devices so field issues can be correlated with configuration history.

Why Use Plaspy with This Configuration​

Configuring the GOTOP G01 to report to Plaspy provides a straightforward path to integrate vehicle location, ignition and alarm events into a single fleet management platform. For organizations that require operational visibility, event-driven alerts and centralized reporting, using the G01 with Plaspy enables real-time monitoring and actionable workflows tied to vehicle inputs such as ACC, SOS and immobilizer controls.

To learn more about Plaspy and view platform features visit https://www.plaspy.com. Manufacturer specifications and device setup methods can change over time; verify the latest device-specific configuration details and firmware behavior with GOTOP at https://www.gotop.cc/.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy