Skip to main content

GOTOP - G01-4G Configuration

This page describes the public configuration context for using the GOTOP G01-4G tracker with Plaspy. It summarizes the practical server settings and workflow needed to point the device at Plaspy, explains what to check before setup, and highlights important notes about manufacturer variation. The content focuses on the settings Plaspy requires and how the tracker typically reports location and events to the platform.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol at the server side. Exact manufacturer-side setup steps can vary by device firmware, hardware revision, installation type, or vendor configuration tools, so the guidance here frames the public Plaspy settings and a general workflow rather than every possible device-specific command sequence.

Configuration Overview​

Configuring the G01-4G for Plaspy prepares the device to deliver location, alarm, and telemetry data to the centralized Plaspy platform. The primary goal is to ensure the tracker is reachable by Plaspy's server endpoint, that the correct transport and port are selected, and that the device is validated in the platform so live maps and alerts are available to users.

  • Point the device to the Plaspy server by entering the server domain or IP and the shared port used by Plaspy.
  • Select the transport protocol the device supports, UDP or TCP, and save that setting on the device side.
  • Verify cellular connectivity and that the tracker can send packets to Plaspy's endpoint.
  • Validate the device appears in Plaspy and that position and event messages are being ingested.
  • Confirm alarms like SOS, vibration, and ACC are transmitted and visible in Plaspy dashboards.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol

Typical Requirements Before Setup​

  • Confirm the G01-4G is powered and installed according to the manufacturer guide with antenna and wiring secured.
  • Active cellular SIM card provisioned for data and SMS as required by the device; ensure coverage for the deployment area.
  • Access to the official GOTOP configuration method or software for the G01-4G (manufacturer tool, web interface, or SMS commands).
  • A Plaspy account or platform access to validate device reporting and view incoming telemetry.
  • Basic knowledge of whether the device requires selecting UDP or TCP for server transport or if transport selection is automatic in the device UI.

How This Tracker Connects to Plaspy​

When configured for Plaspy, the G01-4G sends GNSS fixes, alarm events, and vehicle telemetry over cellular data to Plaspy's shared server endpoint and port. Plaspy ingests these messages and converts them into live location updates, alarms, and historical records for fleet monitoring and incident response.

  • The device is configured to report to d.plaspy.com or directly to 54.85.159.138 on port 8888.
  • Choose UDP or TCP on the device if a transport option is required; Plaspy accepts both and will detect the protocol automatically.
  • Regular position reports and alarm messages appear in Plaspy for live mapping and alerting.
  • Telemetry such as ACC (ignition) events, SOS presses, vibration alarms, and power loss are forwarded to Plaspy and recorded against the device.
  • SMS fallback (where supported by the device) provides continuity for select events if data connectivity is temporarily unavailable.

Common Configuration Workflow​

  1. Access the official GOTOP configuration method or software for the G01-4G (manufacturer tool, web UI, or SMS configuration channel).
  2. Enter the Plaspy server address either as domain d.plaspy.com or as IP 54.85.159.138 in the device server setting.
  3. Set the device port to 8888 which is the shared port Plaspy uses for all devices.
  4. Choose UDP or TCP if the device requires transport selection; save the chosen transport.
  5. Apply or save the configuration on the device and follow any manufacturer prompts to commit settings.
  6. Restart the device if the tool or manufacturer guide requires a reboot for settings to take effect.
  7. Validate that the device reports to Plaspy by checking the platform for incoming position updates and event messages.

Example Configuration Commands​

This model configuration file does not include a universal list of public commands. GOTOP devices are commonly configured using the manufacturer's configuration tool, web interface, or SMS command set, and exact commands or SMS syntax depend on firmware and regional product variants.

When using manufacturer SMS commands or a configuration tool, the essential settings you must supply are:

  • Server domain d.plaspy.com or server IP 54.85.159.138
  • Port 8888
  • Transport UDP or TCP if required by the device

If you need device-specific SMS commands or a command list, consult the GOTOP G01-4G product documentation or the configuration guide provided by your vendor. Plaspy will accept reports on the shared server and automatically detect the tracker protocol when the device sends data to the address and port above.

Configuration Notes​

  • Firmware variations and regional hardware revisions can change command syntax and configuration UI; always confirm with the GOTOP documentation for your device revision.
  • Decide between UDP and TCP based on installer preference and network conditions. Plaspy accepts either and performs automatic protocol detection.
  • The G01-4G supports SMS fallback for certain events; SMS configuration commands (if used) are manufacturer specific.
  • All devices in Plaspy use the same port (8888), which simplifies server configuration across mixed fleets.
  • Keep a copy of your saved configuration and test a device in a controlled environment before mass deployment.

Why Use Plaspy with This Configuration​

Using the GOTOP G01-4G with Plaspy gives organizations centralized visibility into vehicle location, alarms, and telemetry. Plaspy ingests the tracker’s 4G updates and event streams so fleet managers can monitor live positions, respond to SOS and vibration alarms, track ignition state, and manage remote immobilization workflows from a single platform.

To learn more about Plaspy and how it integrates with trackers like the GOTOP G01-4G, visit https://www.plaspy.com. For the most current device specific configuration, firmware details, and command syntax consult the manufacturer website https://www.gotop.cc/ since setup methods and device behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy