Skip to main content

GOTOP - GX6 Configuration

This page documents the public configuration context for using the GOTOP GX6 tracker with Plaspy. It focuses on the practical server and transport values you need to point the device at Plaspy, explains the expected workflow for device setup, and highlights the main prerequisites to validate before integration.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol. Exact manufacturer side setup steps for the GX6 can vary by firmware version, hardware revision, installation type, and the configuration method provided by the vendor, so follow this guide for the Plaspy side of the integration and consult the manufacturer for device specific steps.

Configuration Overview​

This configuration process prepares the GX6 to communicate with the Plaspy platform so the device can report location and events, and appear in Plaspy for monitoring and fleet management.

  • Configure the tracker to send data to the Plaspy server endpoint so location and event messages are delivered.
  • Select the transport option the device supports UDP or TCP on the shared Plaspy port.
  • Save and apply settings using the official GOTOP configuration method so the device uses the new server values.
  • Restart or power cycle the device if required to activate the new settings.
  • Validate connectivity on Plaspy to confirm the GX6 is reporting and visible in your account.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol and all devices use the same port

Use either the domain d.plaspy.com or the server IP 54.85.159.138 when configuring the GX6. The device may be configured using UDP or TCP on port 8888 and Plaspy will automatically detect the incoming protocol.

Typical Requirements Before Setup​

  • The GX6 must be powered and installed according to the manufacturer instructions so configuration changes persist.
  • An active cellular data SIM and valid mobile network coverage for 4G LTE or fallback networks as supported by the device.
  • Access to the official GOTOP configuration method such as their configuration tool software or SMS/serial commands if provided by the vendor.
  • Knowledge of any required APN settings for the SIM and a way to enter or provision them through the device configuration interface.
  • A way to test connectivity such as observing device reporting in Plaspy or using the manufacturer verification tools.
  • Confirmation of the device firmware version and hardware revision to ensure the correct configuration procedure.

How This Tracker Connects to Plaspy​

When configured for Plaspy, the GX6 is set to report its location and status messages to the shared Plaspy server endpoint and port so the platform receives and processes telemetry for visibility and monitoring.

  • The tracker sends periodic or event driven location packets to d.plaspy.com or 54.85.159.138 on port 8888.
  • Transport can be UDP or TCP depending on device configuration and installer preference.
  • Plaspy detects the tracker protocol automatically and maps incoming messages to the appropriate parser.
  • Events reported by the GX6 such as geofence violations, overspeed, ACC state changes, and power alarms are forwarded to the platform for alerts and logging.
  • Successful configuration results in the GX6 appearing in Plaspy where location, history, and event reports are available for fleet monitoring.

Common Configuration Workflow​

  1. Access the official GOTOP configuration method or software supplied with the GX6 by the vendor or manufacturer.
  2. Enter the Plaspy server address using either d.plaspy.com or 54.85.159.138 as the server endpoint.
  3. Set the server port to 8888 which is the standard port used by Plaspy for all devices.
  4. Choose UDP or TCP transport if the GX6 requires a transport selection.
  5. Apply or save the configuration in the device tool and confirm the settings were written.
  6. Restart or power cycle the GX6 if the manufacturer instructions require a reboot for new settings to take effect.
  7. Validate that the device reports to Plaspy by checking for connection or telemetry arrival in the platform.

Example Configuration Commands​

The GX6 configuration method can differ by firmware and vendor tools. Because the manufacturer provides the configuration interfaces, exact command formats or SMS strings are not included here. Use the official GOTOP configuration tool or reference the GX6 user manual for device specific commands and examples.

If your installer documentation includes command examples for setting server address port transport or APN those should be used exactly as provided by the manufacturer. Preserve any placeholders such as APN or user credentials as required by your SIM provider when entering settings.

Configuration Notes​

  • Firmware and hardware revisions can change the configuration interface and available commands so always confirm the steps for your device revision.
  • TCP and UDP each have trade offs UDP is stateless and often simpler while TCP provides connection level reliability choose the transport that fits your network and device behavior.
  • Plaspy uses the same port for all supported devices and automatically detects the incoming protocol to match the correct parser.
  • If your setup uses an APN or SIM authentication be sure to provision those parameters through the GOTOP tool or configuration method.
  • Installer practices and regional variants of the GX6 may require slightly different steps for entering the server address or saving configuration.

Why Use Plaspy with This Configuration​

Configuring the GOTOP GX6 to report to Plaspy gives fleet operators a consistent platform for vehicle location, event monitoring, and operational oversight. With Plaspy handling protocol detection and using a shared server endpoint and port, integration focuses on the device side settings and verification rather than protocol mapping.

To learn more about Plaspy and how your fleet can use the platform visit https://www.plaspy.com. For the latest GX6 device specific setup details firmware notes and official configuration tools verify information on the manufacturer site https://www.gotop.cc/ as device behavior and setup methods can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy