Skip to main content

GOTOP - T0500 Configuration

This page documents the public configuration context for using the GOTOP T0500 solar animal GPS tracker with Plaspy. It focuses on the practical server settings and the general setup workflow needed to point a T0500 at Plaspy so location and telemetry data appear in the platform. The content here uses public Plaspy configuration values and the T0500 device description as the factual basis for setup guidance.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when data arrives. Manufacturer side setup steps for the T0500 can vary by firmware version, hardware revision, installation type, and the configuration tools provided by GOTOP or local vendors. Use the steps below as a practical reference and consult manufacturer documentation for device specific commands or GUI options.

Configuration Overview​

Preparing a T0500 for use with Plaspy means configuring the device to send its location and telemetry to Plaspy's shared server endpoint and verifying that data reaches the platform. The process is mainly about setting the correct server endpoint and transport, ensuring network and power readiness, and confirming the device reports successfully in Plaspy.

  • Configure the tracker to report to the Plaspy server endpoint using the domain or IP provided
  • Select the correct transport type if the device requires a UDP or TCP choice
  • Set the device to use port 8888 which Plaspy uses for all supported devices
  • Validate connectivity from the field device to the Plaspy server and confirm messages arrive
  • Enable and test the T0500 telemetry such as motion, tamper, and battery status so alerts appear in Plaspy

Plaspy Server Settings​

Use these public Plaspy settings when configuring the T0500. Plaspy uses the same port for all supported devices and automatically detects the tracker protocol when data is received.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol when the device connects

Typical Requirements Before Setup​

  • Access to the official GOTOP T0500 configuration method or software for your firmware and variant
  • Charged device battery and correct physical installation on the collar with tamper sensors enabled if used
  • Active cellular connectivity and a data capable SIM card provisioned for GPRS or the network mode of the device variant
  • Network coverage at the deployment site sufficient for GPRS data uploads
  • A Plaspy account or access to a Plaspy-enabled platform where you can view incoming device data
  • Basic device identifiers such as IMEI so you can confirm the correct unit in Plaspy after setup

How This Tracker Connects to Plaspy​

The T0500 sends location and telemetry over the device cellular data link to the Plaspy cloud endpoint. In practice the tracker is configured with the Plaspy server address and port, and Plaspy ingests the telemetry, applies protocol detection, and surfaces location, alerts, and history to users.

  • The tracker is pointed at d.plaspy.com or 54.85.159.138 and uses port 8888 for uploads
  • Device messages are sent over UDP or TCP depending on the device configuration and network conditions
  • Plaspy automatically detects the tracker protocol and processes incoming GPS and LBS positioning
  • Alerts such as collar cut, motion, and low battery are forwarded to the Plaspy platform for notification and history
  • Successful configuration results in real time location and telemetry visible within Plaspy dashboards and tools

Common Configuration Workflow​

Follow these practical steps when configuring a T0500 to work with Plaspy. Exact GUI layouts or SMS/CLI commands depend on the manufacturer tools and firmware.

  1. Access the official GOTOP configuration method or software for the T0500, such as the manufacturer web tool, PC client, or documented SMS command set
  2. In the device server settings enter the Plaspy server domain d.plaspy.com or the server IP 54.85.159.138
  3. Set the device port to 8888 which Plaspy uses for all supported devices
  4. Choose UDP or TCP transport if the device requires an explicit transport selection
  5. Apply or save the configuration in the device tool following the manufacturer procedure
  6. Restart the device if the vendor documentation requires a reboot for new settings to take effect
  7. Validate that the device reports to Plaspy by checking for the device IMEI or identifier in your Plaspy account and confirming recent position updates

Example Configuration Commands​

The exact command set and syntax for the GOTOP T0500 vary by firmware and vendor tool. Because manufacturer methods differ, use the official GOTOP command reference or configuration utility for precise commands. Typical vendor methods include a web based or PC configuration utility and an SMS command interface for field updates. If you have a list of GOTOP T0500 public commands from official documentation, apply them in the order specified by the manufacturer and include the Plaspy server domain d.plaspy.com or IP 54.85.159.138 and port 8888 as shown in the common workflow.

Configuration Notes​

  • Firmware versions and hardware variants can change command syntax and menu locations so verify commands against the T0500 firmware release notes
  • Installer workflows in the field commonly prefer SMS based updates for single units and vendor software for bulk provisioning
  • Choose UDP or TCP according to reachability and reliability in your deployment area; Plaspy accepts either and detects protocol automatically
  • All devices in Plaspy use the same port 8888 which simplifies provisioning and firewall rules for fleets
  • Confirm device identifiers such as IMEI during provisioning so the correct unit is mapped in Plaspy after the first successful upload

Why Use Plaspy with This Configuration​

Using the GOTOP T0500 with Plaspy gives livestock managers and field operators a practical way to collect long term location and alert telemetry from solar assisted collar trackers. Plaspy processes the T0500 streams and makes position, tamper, motion, and battery events available for immediate notification, historical playback, and operational decision making.

To learn more about Plaspy visit https://www.plaspy.com and for the latest device specific configuration instructions and firmware details check the GOTOP manufacturer site https://www.gotop.cc/ . Please verify device specific configuration methods and firmware behavior on the manufacturer site because setup procedures and features can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy