Skip to main content

GOTOP - VT-360 Configuration

This page covers the public configuration context for using the GOTOP VT-360 tracker with Plaspy. It summarizes the shared server settings Plaspy expects, explains the practical steps most installers follow, and highlights the typical prerequisites that let the VT-360 communicate with the platform. The VT-360 is a GPS GSM GPRS device and supports real time tracking over GPRS as well as SMS based location links, so this guide focuses on preparing those communication paths for Plaspy.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when the device connects. Exact manufacturer side setup steps can vary by firmware, hardware revision, installation type, and the vendor tools you use to configure the VT-360. Treat this document as practical public guidance and verify any device specific details in the official GOTOP documentation when needed.

Configuration Overview​

The goal of this configuration process is to point the VT-360 at Plaspy so the device can report location and alarm events reliably to the platform. You will prepare the tracker for data connection, confirm network access, and verify the device becomes visible in Plaspy.

  • Configure the tracker to send data to d.plaspy.com or to the Plaspy server IP on the shared Plaspy port
  • Ensure the VT-360 has an active GPRS capable SIM and correct APN if required by your mobile operator
  • Choose transport UDP or TCP if the device requires a transport selection when sending to Plaspy
  • Save and apply the manufacturer configuration and restart the device when required
  • Validate connectivity and that Plaspy receives the first position or event from the tracker

Plaspy Server Settings​

Use these public Plaspy settings when configuring the VT-360 so the device reports to the correct endpoint and port.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP depending on device configuration options
  • Plaspy automatically detects the tracker protocol when the device connects

Note that all devices in Plaspy use the same port so you only need to set port 8888 for supported trackers.

Typical Requirements Before Setup​

  • Confirm the VT-360 is powered and has a charged internal battery if it will be tested outside permanent vehicle power
  • Install an active SIM with data enabled and verify the operator APN if the device will use GPRS
  • Obtain access to the official GOTOP configuration tool or method required for your unit and firmware
  • Know the device IMEI or identifier so you can register or identify the device in Plaspy after it connects
  • Have a basic checklist of alarms and inputs you want enabled so you can test reporting after configuration

How This Tracker Connects to Plaspy​

When configured for Plaspy the VT-360 will send its position and event information to the shared Plaspy endpoint and port. Plaspy receives the data and maps it to the device record so you can monitor locations and alarms in the platform.

  • The VT-360 reports location and status data to d.plaspy.com or 54.85.159.138 on port 8888
  • Transport can be UDP or TCP depending on how the device is configured
  • Real time reporting over GPRS delivers periodic positions and alarms to Plaspy for visibility and monitoring
  • SMS based location links remain useful for quick checks or as a fallback where GPRS is unavailable
  • Plaspy automatically detects the device protocol once the tracker initiates communication

Common Configuration Workflow​

  1. Access the official GOTOP configuration method for the VT-360, using the manufacturer software, SMS commands, or configuration cable as supported by your unit
  2. Enter the Plaspy server as either the domain d.plaspy.com or the IP 54.85.159.138 in the server or APN settings field
  3. Set the server port to 8888 which is the shared Plaspy port for all supported devices
  4. Choose UDP or TCP if your version of the VT-360 requires a transport selection
  5. Configure any required APN information so GPRS can connect if the device uses mobile data
  6. Apply or save the configuration then restart the device if required by the manufacturer
  7. Validate that the device reports to Plaspy by confirming the first position or event appears in your Plaspy device list

Example Configuration Commands​

The exact configuration commands and method vary by GOTOP firmware and the configuration tool you use. Some installers configure the VT-360 using manufacturer SMS commands, while others use a USB or serial configuration tool. Regardless of method, the critical server and port values to use are d.plaspy.com or 54.85.159.138 and port 8888 with UDP or TCP selected if prompted. Plaspy will detect the tracker protocol automatically when the device connects.

If you are using SMS based configuration supplied by the manufacturer consult GOTOP documentation for the exact command templates. Keep the Plaspy endpoint and port handy when substituting into those templates.

Configuration Notes​

  • Firmware and hardware revisions can change available menu options or SMS command formats; check the GOTOP documentation that matches your device revision
  • If the device offers both UDP and TCP choose the transport that matches your network and installer preference; Plaspy accepts either
  • SMS configuration can be a quick alternative for remote tuning but verify GPRS reporting after applying SMS commands
  • Remember that all Plaspy devices use the same port so you will set port 8888 for this tracker as well
  • Manufacturer tools may present the server field as domain or IP use either d.plaspy.com or 54.85.159.138

Why Use Plaspy with This Configuration​

Configuring the GOTOP VT-360 to report to Plaspy provides centralized visibility for vehicle locations, alarms, and operational events. For fleet managers and installers the VT-360 offers several alarm and input features that can be routed into Plaspy to improve monitoring, security, and operational decision making.

To learn more about Plaspy visit https://www.plaspy.com and review the full set of platform features. For the latest device specific configuration commands, firmware notes, and installation guidance always verify details on the official GOTOP website https://www.gotop.cc/ since manufacturer specifications and setup methods can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy