Skip to main content

GPSMarker - M60 Configuration

This page covers the public configuration context for using the GPSMarker M60 with the Plaspy platform. It summarizes the server settings and the practical setup workflow required to point an M60 tracker at Plaspy so devices become visible and report location and sensor data. The information below focuses on publicly available configuration guidance and on the shared Plaspy connection values you need to apply on the device or with the manufacturer's tools.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while the exact manufacturer side setup steps can vary by firmware, hardware revision, installation type, and vendor tools. The M60 itself is described as a versatile tracker with long battery life, an integrated temperature sensor, optional SMS or GPRS configuration paths, and compatibility with free fleet servers; use this page to align those capabilities with Plaspy connection requirements.

Configuration Overview​

Configuring the M60 for Plaspy prepares the device to send its position and any supported sensor information to the Plaspy platform so you can monitor the device in your fleet view. The goal is to set a single shared endpoint and port on the tracker, ensure the device has network connectivity, and confirm that Plaspy accepts and recognizes the device protocol automatically.

  • Point the tracker to the Plaspy server endpoint so telemetry is routed to Plaspy
  • Ensure the device has an active data path and any required APN settings for GPRS
  • Choose the transport type the device supports and save the network configuration
  • Validate that the M60 reports location and temperature sensor data to Plaspy
  • Confirm visibility and correct device identification inside the Plaspy platform

Plaspy Server Settings​

Use the following Plaspy server settings when configuring the GPSMarker M60. Plaspy requires these public values for correct routing of device data.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol

All devices in Plaspy use the same port, so set port 8888 on the device regardless of model.

Typical Requirements Before Setup​

  • A powered M60 unit with sufficient battery or external power for configuration and initial testing
  • Access to the official GPSMarker configuration method or tools provided by the manufacturer
  • A working SIM card with mobile data and correct APN settings if using the GPRS data channel
  • Network coverage where the device will operate so it can establish a data session
  • Knowledge of whether you will configure via the manufacturer web tool, desktop software, SMS commands, or another vendor method
  • Access to your Plaspy account or platform administrator to confirm device registration and visibility

How This Tracker Connects to Plaspy​

When configured for Plaspy, the M60 is set to send its tracking packets to the shared Plaspy server endpoint and port. Plaspy receives the incoming data over the selected transport and automatically detects the tracker protocol so the device appears and updates in the platform.

  • The tracker sends location and available sensor data to d.plaspy.com or 54.85.159.138 on port 8888
  • You may configure the M60 to use UDP or TCP transport depending on its configuration interface
  • Plaspy inspects incoming packets and automatically detects the correct protocol for the M60
  • Once connected, the device becomes visible in Plaspy for monitoring and event reporting
  • Sensor readings such as temperature can be relayed to Plaspy if enabled on the device

Common Configuration Workflow​

  1. Access the official GPSMarker configuration method or software provided by the manufacturer for the M60.
  2. Ensure the device has network connectivity and, if required, enter the correct APN settings for the SIM card.
  3. Enter the Plaspy server address by using either d.plaspy.com or 54.85.159.138 as the server endpoint.
  4. Set the server port to 8888.
  5. Choose UDP or TCP if the device requires a transport selection.
  6. Apply or save the configuration on the device or within the manufacturer tool.
  7. Restart the device if required by the configuration method.
  8. Validate that the M60 reports to Plaspy and appears in the platform with expected location and sensor updates.

Example Configuration Commands​

The exact commands and their syntax depend on the GPSMarker M60 firmware and the manufacturer configuration tool you are using. Some M60 units support configuration via software, a web interface, or SMS commands, while others prefer direct configuration through the vendor application. Because manufacturer tools differ by firmware and region, consult the GPSMarker documentation for exact command formats.

If you have a configuration method that accepts server, port, and transport values, use these exact values for Plaspy:

  • Server: d.plaspy.com (or 54.85.159.138)
  • Port: 8888
  • Transport: UDP or TCP

Example placeholder for APN fields when using a manufacturer tool:

  • APN: enter your mobile operator APN as provided by your carrier
  • APN username: enter if required by your mobile operator
  • APN password: enter if required by your mobile operator

If you locate public SMS or CLI commands in your GPSMarker documentation, apply the server and port values above and preserve any placeholders the manufacturer requires.

Configuration Notes​

  • Firmware and hardware revisions can change command formats and available configuration options; always check the device firmware notes.
  • Plaspy supports both UDP and TCP and automatically detects the tracker protocol, but selecting the transport the device prefers can simplify debugging.
  • Devices that support configuration without SMS or via GPRS may offer multiple setup paths; choose the path that fits your deployment and installer experience.
  • Since all Plaspy devices use the same port, setting port 8888 uniformly reduces configuration errors across mixed fleets.
  • Manufacturer documentation is the authoritative source for device specific commands, reset procedures, and advanced settings.

Why Use Plaspy with This Configuration​

Using the GPSMarker M60 with Plaspy provides a straightforward way to integrate a long battery life tracker and its temperature sensor into an operational fleet view. Pointing the M60 at Plaspy with the shared server endpoint and port lets organizations consolidate tracking data, monitor device locations, and receive sensor updates through a single platform that automatically recognizes the device protocol.

Learn more about Plaspy and how it can consolidate tracking for mixed fleets at https://www.plaspy.com. For the latest device specific setup details, firmware notes, and manufacturer instructions, verify the current information on the GPSMarker website https://gpsmarker.ru/. Device specific configuration methods and firmware behavior can change over time so checking the manufacturer resources will ensure the most accurate setup steps.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy