Skip to main content

Intellitrack - Intellitrac X8 Configuration

This page covers the public configuration context for using the Systech Intellitrac X8 GPS tracker with Plaspy. It summarizes the practical server settings and the typical steps required to point the tracker at Plaspy so the device can deliver location and event data to the platform. The guidance below focuses on the shared Plaspy server endpoint and common setup workflow while relying on public device capabilities described by the manufacturer.

Plaspy uses consistent server settings across supported devices and automatically detects the tracker protocol, but exact manufacturer side setup steps can vary by firmware, hardware revision, installation type, and vendor tools. Use this guide to understand the required server values and general workflow, and always cross check manufacturer documentation or configuration software for device specific commands and options.

Configuration Overview​

Preparing an Intellitrac X8 for use with Plaspy is primarily about configuring the device to send its location and status to the Plaspy endpoint and then verifying that the platform receives and displays that data. The Intellitrac X8 supports GSM GPRS connectivity and can deliver telemetry over TCP or UDP, which provides flexible transport options for integration.

  • Configure the tracker to point to the Plaspy server endpoint so data is routed to the platform
  • Select the appropriate transport mode on the tracker when the device requires a TCP or UDP choice
  • Validate GPRS connectivity and any required SIM network settings so the device can reach Plaspy
  • Verify the tracker appears and reports in Plaspy after configuration so location and events are visible
  • Save and apply changes using the manufacturer tool or SMS method, then restart the device if required

Plaspy Server Settings​

Use the following public Plaspy settings when configuring the Intellitrac X8:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol

Plaspy uses the same port for all supported devices and protocol detection is handled server side, so the key device-side values are the server domain or IP and the port.

Typical Requirements Before Setup​

  • Stable power and battery present or vehicle power connected so the tracker stays online during configuration
  • Active SIM card with data or GPRS enabled and appropriate operator APN configured
  • Access to the official Intellitrac X8 configuration method such as vendor software, serial interface, or SMS command set
  • Physical antenna and any external audio or serial connections installed if required by your installation
  • Knowledge of the device model and firmware version so you can follow the correct manufacturer instructions
  • A means to restart the device after applying new network settings

How This Tracker Connects to Plaspy​

When configured for Plaspy, the Intellitrac X8 sends its location and device data to the shared Plaspy endpoint and port so Plaspy can display position and event information in the platform. The device can use its GSM GPRS link to deliver telemetry over either TCP or UDP to the Plaspy server.

  • The tracker reports position and status updates to d.plaspy.com or 54.85.159.138 on port 8888
  • Transport can be selected as TCP or UDP on the device depending on installer preference or firmware options
  • Plaspy automatically detects the tracker protocol so the server will parse incoming data appropriately
  • Event inputs and basic telemetry are transmitted to the Plaspy endpoint so they appear in the platform for monitoring
  • The shared port 8888 is used by Plaspy for all supported devices to simplify configuration

Common Configuration Workflow​

  1. Access the official Intellitrac X8 configuration method or software provided by the manufacturer or vendor.
  2. Locate the server or host configuration fields in the device setup interface.
  3. Enter the Plaspy server domain d.plaspy.com or the server IP 54.85.159.138.
  4. Set the device port to 8888 as this is the port Plaspy uses for all devices.
  5. Choose UDP or TCP if the device requires a transport selection.
  6. Apply or save the configuration in the manufacturer tool or via SMS commands as documented by the vendor.
  7. Restart the device if required by the firmware or after applying network settings.
  8. Validate that the device reports to Plaspy and that position and event data are visible in the platform.

Example Configuration Commands​

The exact commands and the method to apply them depend on the manufacturer tool, firmware version, and whether you use serial, USB, or SMS configuration. The Intellitrac X8 family commonly provides configuration through vendor software or configurable SMS commands; follow the official Intellitrac documentation or your vendor tool for the correct command format and any required authentication.

If you are using SMS-based configuration with your device firmware, manufacturer documentation will list the exact SMS command strings and any placeholders required for APN or authentication fields. Always preserve placeholders and replace them with your network operator details when instructed.

Configuration Notes​

  • Firmware differences and hardware revision can change the exact menu names, command syntax, and available transport options. Check the device firmware documentation before making changes.
  • Choose UDP for lower overhead or TCP for a connection oriented flow if your installation and firmware support both; test both if behavior differs.
  • Ensure the SIM APN and network authentication are configured correctly for GPRS data access to allow the tracker to reach d.plaspy.com.
  • When possible, use the device vendor configuration tool rather than raw SMS to reduce the chance of typos and to preserve device settings.
  • Keep a note of the device software version and configuration steps you used to simplify future maintenance and troubleshooting.

Why Use Plaspy with This Configuration​

Using the Intellitrac X8 with Plaspy gives organizations a straightforward path to convert the device's GPS and GPRS capabilities into platform visibility for fleet monitoring, security events, and operational oversight. The tracker’s ability to deliver telemetry over TCP or UDP and Plaspy’s automatic protocol detection reduce configuration complexity and speed integration.

To learn more about Plaspy and supported device integrations visit https://www.plaspy.com. For the most current device specific configuration instructions, firmware behavior, and manufacturer details verify information on the official manufacturer website https://www.systech-iot.com/.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy