Skip to main content

iStartek - VT300-L Configuration

This page covers the public configuration context for using the iStartek VT300-L tracker with the Plaspy platform. It explains the shared Plaspy server settings and the common, manufacturer-visible setup steps you can use to point a VT300-L to Plaspy for real-time location and telemetry reporting. Where manufacturer commands are publicly available they are included below as examples.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while the exact manufacturer-side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools. The VT300-L supports SMS and GPRS configuration in public documentation; use the manufacturer method appropriate to your device and confirm any firmware-specific commands with iStartek documentation.

Configuration Overview​

The goal of configuration is to prepare the VT300-L to reliably send location and event data to Plaspy so devices become visible in your fleet management workspace. This includes ensuring the device has valid mobile connectivity, setting APN and server parameters, choosing the transport method if required, and validating that messages are reaching the Plaspy endpoint.

  • Configure APN and network parameters so the VT300-L can establish a GPRS/4G session.
  • Set the Plaspy server endpoint and port so the tracker uploads to Plaspy.
  • Choose UDP or TCP transport if the device prompts for a transport selection.
  • Verify reporting interval and device timers so location updates meet your monitoring needs.
  • Validate connectivity by checking parameters and confirming the device appears in Plaspy.

Plaspy Server Settings​

  • Server domain: d.plaspy.com
  • Server IP: 54.85.159.138
  • Port: 8888
  • Transport: UDP or TCP supported (device may allow selecting UDP or TCP)
  • Plaspy automatically detects the tracker protocol and Plaspy uses the same port for all supported devices

Typical Requirements Before Setup​

  • A powered VT300-L device with an active Nano SIM that has data enabled and SMS capability.
  • Access to the VT300-L configuration method supported by your unit (SMS commands or manufacturer software).
  • APN details from the mobile operator for GPRS/4G data connectivity.
  • A mobile phone or SMS gateway to send configuration SMS if using SMS commands.
  • A stable power connection or charged internal battery to avoid interruptions during configuration.
  • Access to the iStartek official documentation for firmware specific notes and any vendor utilities.

How This Tracker Connects to Plaspy​

When configured to Plaspy, the VT300-L will initiate a data session and send its location, status, and event messages to the shared Plaspy server endpoint and port. Plaspy handles protocol detection so the same server and port settings can be used across devices, simplifying large deployments.

  • The tracker uploads position and telemetry to d.plaspy.com or the equivalent IP 54.85.159.138 on port 8888.
  • The device may be configured to use UDP or TCP transport depending on installer choice and firmware support.
  • Plaspy automatically detects the tracker protocol so device messages are processed without custom protocol selection on the server side.
  • Update intervals (timers) determine how frequently the VT300-L reports to the Plaspy endpoint.
  • Event reports such as alarms, ignition changes, and telemetry are sent to the same Plaspy endpoint for platform visibility.

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or software for the VT300-L (SMS commands or vendor tool).
  2. Configure the APN using the operator APN values provided by your mobile network operator.
  3. Enter the Plaspy server domain d.plaspy.com or the IP address 54.85.159.138.
  4. Set the server port to 8888.
  5. Choose UDP or TCP if the device requires a transport selection.
  6. Apply or save the configuration and restart the device if the firmware requires a restart to apply changes.
  7. Validate that the device reports to Plaspy by checking device parameters and confirming visibility in the Plaspy platform.

Example Configuration Commands​

The VT300-L can be configured by SMS using the following publicly documented commands. Preserve the placeholders when substituting your operator APN credentials. Send each command as an SMS to the tracker in the order indicated where appropriate.

  1. Optional factory reset (use only during initial provisioning or when needed):
FACTORY#
  1. Set the time zone to UTC+0 (example command from public docs):
GMT,E,0#
  1. Set the operator APN. Replace [apn] with your mobile operator APN. If your APN requires username or password, supply [apnu] and [apnp] respectively as additional comma separated fields.
APN,[apn],[apnu],[apnp]#

Notes: keep the placeholders if no username or password is required; remove the comma fields if not used.

  1. Set the GPRS server to the Plaspy domain on port 8888 (DNS option):
SERVER,1,d.plaspy.com,8888#
  1. Alternatively set the GPRS server to the Plaspy IP on port 8888 (direct IP option):
SERVER,0,54.85.159.138,8888#
  1. Set the reporting interval (example sets updates every 60 seconds):
TIMER,60#
  1. Verify current parameters on the device:
PARAM#

These commands reflect the public SMS configuration flow for this model. Confirm exact command syntax and any reply format with iStartek documentation before mass deployment.

Configuration Notes​

  • SMS-based configuration is commonly supported for the VT300-L; confirm whether your hardware revision accepts SMS commands or requires a USB/vendor tool.
  • Firmware differences may change command syntax or available features; always verify with the device firmware release notes.
  • Choose TCP or UDP based on network reliability and your operational preferences; Plaspy accepts either and will detect the protocol automatically.
  • Keep APN placeholders intact until replaced with operator values. If a username or password is not required, omit those fields according to manufacturer guidance.
  • Test a single device end to end before rolling out a large batch to ensure the platform is receiving data as expected.

Why Use Plaspy with This Configuration​

Configuring the VT300-L to report to Plaspy provides a practical way to centralize vehicle location, telemetry, and event reporting for fleet oversight. Using the shared Plaspy endpoint simplifies server configuration across many devices because the platform uses the same port for every supported tracker and automatically detects the tracker protocol, reducing per-device server setup complexity.

To learn more about Plaspy and platform capabilities visit https://www.plaspy.com. For the latest device specific commands, firmware notes, and installation guidance verify current information at the manufacturer website https://istartek.com/ as device behavior and setup procedures can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy