Skip to main content

Laipac - Starfinder KAMEL Configuration

This page covers the public configuration context for using the Laipac Starfinder KAMEL tracker with Plaspy. It summarizes the practical server settings and setup workflow needed to point the device to Plaspy so the tracker can report location and event data into the platform. The guidance below is intended for installers and fleet managers preparing the device for integration with Plaspy.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when data reaches the platform. Exact manufacturer side steps can vary depending on firmware version, hardware revision, installation method, and vendor configuration tools. Use the manufacturer documentation and configuration tools alongside the Plaspy server values listed below when you perform setup.

Configuration Overview​

The goal of this configuration is to prepare the Starfinder KAMEL to send position and event data to Plaspy so assets become visible and monitored in the Plaspy platform. Typical configuration sets the device server target, transport, and port, then validates that reports arrive at Plaspy.

  • Configure the tracker to report to d.plaspy.com or the equivalent Plaspy server IP
  • Ensure the device is set to use port 8888 which Plaspy requires for all supported trackers
  • Choose UDP or TCP transport if the device firmware requires a transport selection
  • Save and apply settings, then confirm the device is registered and visible in Plaspy
  • Validate connectivity and telemetry delivery so the tracker appears in the Plaspy platform

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol when data arrives
  • All devices in Plaspy use the same port 8888 so a single port configuration is sufficient

Typical Requirements Before Setup​

  • Confirm the Starfinder KAMEL has a charged internal battery or is installed with power applied
  • Have an active cellular SIM and cellular coverage available if the device uses GSM GPRS for reporting
  • Access to the official Laipac configuration method or software used to set server and port
  • Basic device information such as IMEI to identify the unit in Plaspy after it connects
  • A test plan to validate connectivity including location reports and a visibility check in Plaspy

How This Tracker Connects to Plaspy​

The Starfinder KAMEL sends position and event data to a network endpoint that Plaspy accepts. When configured to point at Plaspy, the device will deliver telemetry to the shared server endpoint and port where Plaspy automatically recognizes and parses the supported protocol.

  • Device reports are sent to d.plaspy.com or 54.85.159.138
  • Reports are transmitted on port 8888 which Plaspy uses for all devices
  • Transport may be UDP or TCP depending on device configuration and firmware options
  • Once data reaches Plaspy the platform performs automatic protocol detection and parsing
  • Successful reporting enables live visibility, event alerts, and historical data in Plaspy

Common Configuration Workflow​

  1. Access the official Laipac configuration method or software recommended for Starfinder KAMEL configuration (manufacturer web tool, desktop utility, or SMS instructions)
  2. Enter the Plaspy server domain d.plaspy.com or the server IP 54.85.159.138 as the device reporting endpoint
  3. Set the device reporting port to 8888
  4. Choose UDP or TCP transport on the device if a transport selection is required by the firmware
  5. Apply or save the configuration on the device using the manufacturer tool
  6. Restart the device if the configuration tool or manufacturer instructions require a reboot for settings to take effect
  7. Validate that the device reports to Plaspy by checking device appearance and incoming telemetry within the Plaspy platform

Example Configuration Commands​

The Starfinder KAMEL may be configured using different manufacturer tools or firmware interfaces. Exact commands or SMS formats vary by firmware and vendor toolset, so no universal command set is provided here. Use the Laipac configuration utility or official Laipac documentation to apply the following required server values:

  • Point the device to d.plaspy.com or 54.85.159.138
  • Use port 8888
  • Select UDP or TCP transport if prompted

If your vendor documentation provides specific SMS commands, web forms, or serial commands for server and port, use those exact commands and include the Plaspy values above. Always preserve placeholders from manufacturer examples such as [apn] if they appear in official command templates and replace them with your network values.

Configuration Notes​

  • Firmware differences can change the exact menu labels, command syntax, or transport options; always confirm the device firmware version before applying commands
  • If your Starfinder KAMEL firmware supports both UDP and TCP, test both transports if you encounter connectivity issues; Plaspy will accept either on port 8888
  • Use the IMEI or device identifier to locate and verify the tracker in Plaspy after it first reports
  • Installer practices differ between permanent mount and magnet mount installations; ensure good GPS reception and cellular signal at the installation site
  • Manufacturer documentation may list SMS based, USB, or web based configuration paths; follow the official Laipac steps for your device variant

Why Use Plaspy with This Configuration​

Configuring the Laipac Starfinder KAMEL to report to Plaspy gives organizations a consistent endpoint for asset visibility, alerting, and history. The device is well suited for non powered and powered assets and when paired with Plaspy enables remote monitoring, geofence alerts, and motion based reporting to support recovery and operational workflows.

Learn more about Plaspy and how it supports tracker integration at https://www.plaspy.com. Device specific configuration, firmware behavior, and manufacturer instructions can change over time so please verify the latest setup information on the manufacturer site https://laipac.com/ before final deployment.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy