Skip to main content

LK-GPS - LK210-3G Configuration

This page documents the public configuration context for using the LK-GPS LK210-3G tracker with Plaspy. It explains the shared Plaspy server settings you will point the device to, the common setup workflow, and practical checks to validate that the tracker is reporting correctly to the Plaspy platform. This content is written for installers, fleet managers, and technical users preparing the LK210-3G for live monitoring in Plaspy.

Plaspy uses shared server values across supported devices and automatically detects the tracker protocol once the device connects. Exact manufacturer-side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools, so use the guidance below together with the LK-GPS documentation and manufacturer configuration utilities when available.

Configuration Overview​

The goal of configuration is to prepare the LK210-3G so it reliably communicates with Plaspy and appears in your fleet dashboard. Configuration focuses on pointing the tracker at the Plaspy server, choosing the correct transport, and validating data flow into the platform.

  • Entering Plaspy server settings on the device so telemetry is sent to the correct endpoint.
  • Selecting the transport method the device supports and saving that choice.
  • Verifying the tracker registers and sends periodic location and alert messages to Plaspy.
  • Confirming vibration and tamper alerts are received by the platform after installation.
  • Ensuring battery and standby reporting are visible in the Plaspy dashboard for maintenance planning.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol when the device connects

These values are the public, shared settings used by Plaspy for all supported devices and are the values you will enter into the LK210-3G using the manufacturer tool or SMS commands.

Typical Requirements Before Setup​

  • Confirm the LK210-3G has sufficient battery charge or is connected to a stable power source for initial setup.
  • Have access to the official LK-GPS configuration method or software from the manufacturer.
  • Ensure the device has cellular connectivity enabled with an active SIM card for GSM and SMS support.
  • Verify that you have the device identifier or IMEI available for registration and troubleshooting.
  • Confirm any regional firmware or hardware variant differences with the manufacturer documentation.

How This Tracker Connects to Plaspy​

The LK210-3G is configured to send position, sensor, and alert data to Plaspy using the shared server endpoint and port. Plaspy receives the data and maps the device protocol automatically so the tracker becomes visible in the platform without device-specific server differences.

  • The tracker points to d.plaspy.com or 54.85.159.138 as the destination for telemetry.
  • Messages are transmitted to Plaspy on port 8888 using either UDP or TCP as configured on the device.
  • Plaspy detects the tracker protocol automatically when the first messages arrive.
  • Location updates, vibration alerts, and battery status are forwarded into Plaspy for dashboards and alerts.
  • Platform detection enables immediate use of the tracker inside Plaspy once reporting is validated.

Common Configuration Workflow​

  1. Access the official LK-GPS configuration method or software provided by the manufacturer, or prepare SMS commands if supported.
  2. In the configuration tool or SMS command, enter the Plaspy server as d.plaspy.com or 54.85.159.138.
  3. Set the destination port to 8888 to match Plaspy’s shared port.
  4. Choose the transport method UDP or TCP if the device requires selecting a transport.
  5. Apply or save the configuration in the manufacturer tool or send the SMS apply command if using SMS setup.
  6. Restart the LK210-3G if the manufacturer instructions require a reboot to apply settings.
  7. Validate that the device reports to Plaspy by checking device activity in the Plaspy platform and confirming the tracker is visible and sending updates.

Example Configuration Commands​

The exact commands and syntax for configuring the LK210-3G vary with manufacturer firmware and the configuration interface you use. Typical manufacturer methods include a desktop configuration tool, a mobile app, or SMS command strings. For all methods you will use the Plaspy server settings below when specifying the destination for telemetry.

  • Destination server: d.plaspy.com or 54.85.159.138
  • Destination port: 8888
  • Transport: UDP or TCP

Because device command syntax varies by firmware and vendor tool, refer to the LK-GPS configuration guide or the software utility shipped with the tracker for the precise command format and examples.

Configuration Notes​

  • Firmware differences and regional variants can change the exact configuration steps and command syntax; always confirm with the LK-GPS documentation for your device revision.
  • Choose UDP or TCP according to the device options and network conditions; Plaspy will accept either on port 8888 and will detect the device protocol automatically.
  • If SMS configuration is used, ensure the SIM supports sending and receiving SMS and that the phone number is available for commands.
  • Use the manufacturer's configuration tool when available for clearer validation and to avoid syntax errors often encountered with manual SMS commands.
  • After applying settings, allow a few minutes for the tracker to register with Plaspy and for initial telemetry to appear in the platform.

Why Use Plaspy with This Configuration​

Using the LK210-3G with Plaspy gives organizations consolidated visibility into vehicle and asset locations, real time alarms for tamper or vibration events, and platform-level reporting for maintenance and operations. Pointing the tracker to Plaspy with the shared server and port simplifies large scale deployments because the same destination settings apply to all supported devices.

To learn more about Plaspy and how it can centralize your fleet telemetry, visit https://www.plaspy.com. For the latest device specific commands, firmware notes, and installer guidance verify details with the manufacturer at https://www.lk-gps.com.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy