Skip to main content

LK-GPS - LK630 Configuration

This page provides the public configuration context required to integrate the LK-GPS LK630 CatM tracker with the Plaspy platform. It focuses on the practical, platform-level settings that allow the LK630 to report location and status to Plaspy and describes the typical workflow used to prepare the device for visibility in the Plaspy environment.

Plaspy uses shared server settings for all supported devices and automatically detects the tracker protocol when data arrives. Manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and the vendor configuration tools used by installers or resellers. Use this guide to apply the public Plaspy settings and as a checklist before consulting LK-GPS documentation for device specific procedures.

Configuration Overview​

The configuration process aligns the LK630 tracker to report its location and telemetry into the Plaspy ingestion endpoint so devices become visible, report reliably, and trigger platform alerts. Configuration focuses on defining the server endpoint and transport, validating cellular connectivity, and confirming that the device appears in Plaspy.

  • Set the tracker to report to the Plaspy server endpoint so location and telemetry reach the platform.
  • Choose the transport protocol supported by the device and required by any intermediate tools.
  • Verify cellular CatM connectivity and any required SIM APN or network settings.
  • Save and apply configuration, then validate that Plaspy shows incoming data for the device.
  • Confirm geofence and alert behavior inside Plaspy once the device is visible.

Plaspy Server Settings​

Use the following public Plaspy server settings when configuring the LK630 tracker. Plaspy uses the same port for all supported devices and automatically detects the tracker protocol when data arrives.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol when the device sends data

Typical Requirements Before Setup​

  • A charged LK630 device ready for configuration and testing.
  • Active CatM or 4G cellular connectivity for the device and a data enabled SIM if required by the device carrier.
  • Access to the official LK-GPS configuration method such as the manufacturer app, web portal, SMS command set, or a USB/serial tool as provided by LK-GPS or your vendor.
  • The device IMEI or identifier available for verification in Plaspy after connection.
  • Basic knowledge of the device firmware version and any vendor tools required to save settings.
  • Stable cellular coverage in the test area to allow the device to register and send its first reports.

How This Tracker Connects to Plaspy​

When configured to use Plaspy, the LK630 sends periodic location and status updates to the Plaspy ingestion endpoint. These messages are received on the shared Plaspy port and are processed according to the detected protocol so the device appears in the Plaspy dashboard and generates events.

  • The tracker is configured to report to the Plaspy server endpoint d.plaspy.com or the server IP 54.85.159.138.
  • Messages are sent to port 8888 using either UDP or TCP depending on device support.
  • Plaspy automatically detects the protocol and parses incoming tracker messages for location and telemetry.
  • Location updates, geofence events, and status alerts are forwarded into Plaspy for visualization and rules.
  • Device visibility in Plaspy confirms successful communication and enables historical tracking and notifications.

Common Configuration Workflow​

  1. Access the official LK-GPS configuration method or software provided by the manufacturer or your vendor.
  2. In the device server or APN settings, enter the Plaspy server address using d.plaspy.com or the server IP 54.85.159.138.
  3. Set the reporting port to 8888 as required by Plaspy.
  4. Choose UDP or TCP if the device requires transport selection and save that choice.
  5. Apply or save the configuration on the tracker using the manufacturer tool or command set.
  6. Restart the device if the manufacturer instructions require a reboot to apply network changes.
  7. Validate that the device reports to Plaspy by checking device visibility and recent location updates in the Plaspy platform.

Example Configuration Commands​

The exact configuration commands and formats vary by LK-GPS firmware and the vendor tool used to provision the LK630. Manufacturer apps or SMS command sets are common delivery methods for configuration. Because specific command syntax depends on LK-GPS firmware and distribution, consult the official LK-GPS documentation or your vendor for the exact commands to set server, port, and transport.

If you have manufacturer provided commands, apply them in the order recommended by LK-GPS. Typical command steps will set server address, port, transport, and optionally APN parameters before saving and restarting the device.

Configuration Notes​

  • Firmware differences across LK630 revisions can change command syntax or menu locations in manufacturer tools; always verify the firmware version before applying commands.
  • Choose UDP or TCP based on device capability and installer preference. Plaspy supports both transports on port 8888 and will detect the protocol automatically.
  • Confirm SIM APN settings if the device requires them; some configurations will not transmit data until APN is correctly set for the mobile operator.
  • Device identifiers such as IMEI are helpful during validation to match the physical device with the device entry in Plaspy.
  • Market specific variants or vendor customizations may alter how settings are applied; consult LK-GPS materials for changes.

Why Use Plaspy with This Configuration​

Using the LK630 with Plaspy centralizes pet tracking data into a single platform designed for visibility, notification, and historical analysis. Plaspy captures the location and telemetry the LK630 transmits, enabling live tracking, geofence alerts, and consolidated monitoring across many devices.

To learn more about Plaspy visit https://www.plaspy.com. Device specific configuration methods, firmware behavior, and vendor details can change over time, so verify the latest setup and command reference on the manufacturer site https://www.lk-gps.com.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy