Skip to main content

LK-GPS - LK880 Configuration

This page covers the public configuration context for using the LK-GPS LK880 tracker with Plaspy. It summarizes the practical server settings and setup workflow that you will generally apply when integrating the LK880 with Plaspy for real-time tracking, geo-fence alerts, historical tracks, blind zone supplementary reporting, and other platform features described by the manufacturer.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol. Exact manufacturer-side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools, so use this page as a practical integration guide and verify device-specific procedures with LK-GPS documentation.

Configuration Overview​

The goal of configuration is to point the LK880 at the Plaspy server and validate that it sends the expected position and status messages so the device becomes visible and manageable inside Plaspy. This involves setting the server endpoint, selecting the transport if required by the device, and confirming connectivity from the field.

  • Configure the LK880 to report to Plaspy using the shared server endpoint and port
  • Select UDP or TCP transport where the device firmware requires a transport choice
  • Verify mobile data connectivity and any required APN settings for the device SIM
  • Confirm the device appears in Plaspy and is sending regular position updates
  • Test geo-fence and alert behavior once the device shows as online

Plaspy Server Settings​

Use the following public Plaspy settings when configuring the LK880. These are the values Plaspy expects for device connections.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP depending on the device configuration
  • Plaspy automatically detects the tracker protocol

Note that Plaspy uses the same port for all supported devices, so the port value is shared across tracker models and need not be changed per device type.

Typical Requirements Before Setup​

  • Confirm the LK880 has a charged battery and is powered on
  • Install a SIM card with active data service and confirm network registration on 4G
  • Obtain access to the official LK-GPS configuration method or software from the vendor
  • Ensure you have the device IMEI or identifier handy for later validation inside Plaspy
  • Prepare to configure the device server endpoint to d.plaspy.com or 54.85.159.138 and port 8888
  • Be ready to select UDP or TCP if the device requires transport selection

How This Tracker Connects to Plaspy​

When correctly configured, the LK880 will send periodic position and status reports to the Plaspy endpoint so the device can be tracked and monitored within the platform. Plaspy receives those messages on the common port and handles protocol identification automatically.

  • The tracker is set to report to the shared Plaspy server endpoint and port
  • Data is transmitted over either UDP or TCP based on the device configuration
  • Plaspy automatically detects the device protocol and parses incoming messages
  • Position updates, geo-fence events, and alarms are forwarded into the Plaspy platform
  • Successful configuration enables real-time visibility and historical track queries in Plaspy

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or software provided by LK-GPS for the LK880
  2. In the device server or platform settings enter d.plaspy.com or 54.85.159.138 as the server address
  3. Set the port to 8888 which is the shared Plaspy port used across devices
  4. Choose UDP or TCP if the tracker firmware requires an explicit transport selection
  5. Apply or save the configuration in the manufacturer tool or device interface
  6. Restart the device if the firmware requires a reboot for settings to take effect
  7. Validate that the device reports to Plaspy by checking for online status and initial position updates

Example Configuration Commands​

No public device-specific command set is provided in this document. Exact configuration commands and the configuration interface vary by manufacturer tool, firmware, and regional device variants. LK-GPS devices may be configured via vendor software, mobile apps, or SMS/AT commands depending on the model and firmware revision. For device-level command syntax or SMS configuration strings consult the official LK-GPS configuration guide from the manufacturer.

If you have a specific command list from LK-GPS or vendor documentation, follow that sequence and use the server settings listed earlier: d.plaspy.com or 54.85.159.138 and port 8888. Plaspy will accept either UDP or TCP and will detect the protocol automatically.

Configuration Notes​

  • Firmware versions and hardware revisions can change configuration menus and required steps; always check the device release notes
  • Choose UDP or TCP based on the manufacturer guidance and network reliability considerations in your deployment area
  • Ensure the SIM APN and mobile data settings match the SIM provider requirements so the device can reach d.plaspy.com
  • If using SMS configuration, confirm message formats with LK-GPS documentation before sending commands
  • After initial setup allow a few position cycles for Plaspy to register and display the device in the platform

Why Use Plaspy with This Configuration​

Using Plaspy with the LK880 lets you centralize location, status, and alert data from the device into a single fleet or pet tracking platform. Plaspy's shared server endpoint and automatic protocol detection reduce the per-device complexity of integration, making it straightforward to add LK880 trackers alongside other supported devices.

To learn more about Plaspy and how the platform handles device integrations, visit https://www.plaspy.com. For the latest device-specific configuration methods, firmware updates, and manufacturer details please verify information on the LK-GPS website https://www.lk-gps.com.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy