Skip to main content

LK-GPS - LK930 Configuration

This page covers the public configuration context for using the LK-GPS LK930 tracker with Plaspy. It summarizes the practical server settings and workflow needed to direct LK930 device traffic to Plaspy, and explains what to verify before you try to add the device to your Plaspy account. The LK930 description included details such as GSM and GPRS networking, AGPS and WiFi assisted locating, long standby battery operation, and common alerts that make it suitable for vehicle and asset monitoring.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while exact manufacturer-side setup steps can vary by firmware, hardware revision, installation type, and vendor tools. Use the guidance below to prepare the device and apply the public Plaspy endpoint settings; always confirm any device-specific menus or commands against the manufacturer documentation.

Configuration Overview​

The goal of configuring an LK930 for Plaspy is to point the device to the shared Plaspy endpoint and verify reliable reporting so the unit becomes visible and manageable in the platform. This process focuses on network readiness, applying the server endpoint and transport, and validating connectivity from the device to Plaspy.

  • Configure the LK930 to report to the Plaspy server endpoint so location and event data reach the platform.
  • Ensure the device has cellular connectivity, a working SIM, and correct APN if required by your carrier.
  • Choose the transport (UDP or TCP) if the device requires an explicit selection and set the shared Plaspy port.
  • Save and apply changes on the tracker using the manufacturer configuration tool or SMS method.
  • Validate the device appears in Plaspy and that periodic position updates and alerts arrive as expected.

Plaspy Server Settings​

Use the following public Plaspy settings when configuring the LK930:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP depending on tracker configuration options
  • Plaspy automatically detects the tracker protocol so the same port is used for all supported devices

These values are the shared endpoint and port Plaspy provides for compatible trackers including the LK930.

Typical Requirements Before Setup​

  • A charged LK930 or power connected so the device can register on the cellular network.
  • An active SIM card with data enabled and any required APN information for your mobile operator.
  • Access to the official LK-GPS configuration method such as the vendor configuration app, web tool, or SMS command set.
  • A Plaspy account and access to the platform to confirm device visibility after configuration.
  • Basic device information such as the device IMEI and expected reporting interval to aid verification.

How This Tracker Connects to Plaspy​

When configured, the LK930 will send its location and event messages to the Plaspy server endpoint so the platform can display positions, alerts, and event history. The common behavior is direct reporting from the device to the configured server and port.

  • The LK930 is pointed to d.plaspy.com or 54.85.159.138 and uses port 8888 for data transport.
  • The tracker uses either UDP or TCP to send packets based on the transport selected in device settings.
  • Plaspy receives the data and automatically detects the tracker protocol so you do not need to set a per-device protocol in Plaspy.
  • Once the device is reporting, Plaspy will show location updates and any supported alerts the device transmits.
  • Validation in Plaspy confirms the device is reachable and reporting on the shared Plaspy port.

Common Configuration Workflow​

  1. Access the official LK-GPS configuration method or software provided by the manufacturer (for example the vendor app, web portal, or SMS command interface).
  2. In the device server or IP settings, enter d.plaspy.com or 54.85.159.138 as the server endpoint.
  3. Set the port to 8888 to match the Plaspy shared port for all devices.
  4. Choose UDP or TCP if the device requires you to select a transport protocol.
  5. Apply or save the configuration changes using the device tool or send the configured SMS commands as required by the manufacturer.
  6. Restart the LK930 if the device firmware requires a reboot for settings to take effect.
  7. Validate that the device reports to Plaspy by checking for incoming position updates and event messages in your Plaspy account.

Example Configuration Commands​

No manufacturer-specific public command set was provided here. Exact configuration commands and the method to apply them can vary across LK-GPS firmware versions and vendor tools. If you use SMS-based configuration or a vendor utility, follow the official LK-GPS instructions and substitute the server domain or IP and port given above.

If you locate an official command set from LK-GPS that uses plain text or SMS commands, the key elements to include in any command are the Plaspy server endpoint (d.plaspy.com or 54.85.159.138) and port 8888, plus the transport type if required. Keep any placeholders such as APN values intact when applying those commands.

Configuration Notes​

  • Firmware and tool variations can change menu names and command formats; consult LK-GPS documentation for the exact syntax.
  • If your carrier requires an APN, configure the device APN before attempting to report to the Plaspy server so GPRS data is available.
  • Choosing UDP may use fewer resources and is common for tracker reporting, while TCP provides a connection-oriented transport; pick the transport that matches your device behavior and network reliability.
  • Because Plaspy uses a single port for all supported devices and auto-detects protocols, the primary configuration focus is correct server and port entry on the tracker.
  • Market versions of the LK930 may include optional WiFi or magnetic accessories; verify the features and configuration steps for your exact hardware model.

Why Use Plaspy with This Configuration​

Using the LK930 with Plaspy lets organizations and individuals centralize location reporting, alerts, and history in a single platform. Configuring the device to point to the shared Plaspy endpoint and port provides straightforward integration that supports visibility into fleet or asset movements and timely notifications when the tracker reports supported events.

To learn more about Plaspy and platform capabilities, visit https://www.plaspy.com. For the latest LK930 device manuals, firmware notes, and exact configuration commands consult the manufacturer site at https://www.lk-gps.com to verify the most current device specific setup details and instructions.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy