Skip to main content

Megastek - GVT-510 Configuration

This page describes the public configuration context for using the Megastek GVT-510 with Plaspy. It gathers the practical server settings and example commands that are commonly used to point a GVT-510 tracker at the Plaspy platform and validate connectivity. Use this guide alongside the device manual to apply settings that match your installation and firmware.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while exact manufacturer side steps can vary by firmware, hardware revision, installation type, and vendor tools. The GVT-510 can be configured via SMS commands as shown in the manufacturer content included below, but your exact workflow may differ depending on firmware and the tools you use.

Configuration Overview​

The configuration process prepares the tracker to communicate reliably with Plaspy and to appear in the platform for monitoring and alerts. For the GVT-510 this commonly includes setting the device identifier, APN, reporting interval, and the GPRS server endpoint that Plaspy provides.

  • Point the tracker to the Plaspy server endpoint so it can send location and alarm data
  • Configure APN and data credentials so the tracker has GPRS connectivity
  • Set a reporting interval appropriate for your tracking needs and battery or power constraints
  • Validate device identity using the IMEI and confirm the device reports into Plaspy
  • Use the manufacturer SMS commands or configuration tool to apply and save the settings

Plaspy Server Settings​

Use the following public Plaspy connection values when configuring the GVT-510:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol
  • All devices in Plaspy use the same port

Typical Requirements Before Setup​

  • A powered GVT-510 installed or connected to a stable power source
  • An active SIM card with data service and the correct APN settings for your mobile operator
  • Access to the device SIM phone number so you can send SMS configuration commands if using SMS setup
  • The tracker IMEI ready for use when setting the device identifier
  • The GVT-510 user manual or official Megastek configuration reference for firmware specific details
  • Confidence that the device firmware supports the SMS commands shown in this guide

How This Tracker Connects to Plaspy​

When configured, the GVT-510 sends location and event data to the shared Plaspy endpoint so that devices are visible and report updates within the platform. Plaspy receives device messages on the same port for all supported devices and automatically determines the tracker protocol, simplifying server-side configuration.

  • The tracker is set to report to the Plaspy server endpoint and port
  • Location updates and alarm events are transmitted over GPRS to the server
  • Plaspy processes incoming messages and links them to the device IMEI for visibility
  • The platform reports status and historical points once the device communications are established
  • Automatic protocol detection in Plaspy eliminates the need to specify protocol on the server side

Common Configuration Workflow​

  1. Access the official Megastek configuration method for your device, typically SMS commands or the vendor configuration tool or software.
  2. Enter the Plaspy server using either the domain d.plaspy.com or the direct server IP 54.85.159.138 as required by the device.
  3. Set the server port to 8888 in the device settings.
  4. Choose UDP or TCP if the device requires explicit transport selection.
  5. Apply or save the configuration on the device and send any required confirmation commands.
  6. Restart the tracker if the device firmware recommends a reboot after setting network parameters.
  7. Validate that the device reports to Plaspy and appears in the platform using the device IMEI and recent telemetry.

Example Configuration Commands​

The GVT-510 can be configured using SMS commands. The example commands below are drawn from the public Megastek configuration content. The sample commands use the device default password 000000. Send these SMS messages to the GVT-510 device phone number. Replace placeholders with your device values.

  • Set the device ID using the device IMEI. Replace [IMEI_15] with the last 15 digits of the device IMEI:
M000000,22,[IMEI_15]
  • Set the operator APN. Replace [apn] with your carrier APN. If your operator requires APN username and password, include [apnu] and [apnp]:
M000000,23,[apn]

Optional with username and password:

M000000,23,[apn],[apnu],[apnp]

(Placeholders explanation: [apn] = APN, [apnu] = APN username, [apnp] = APN password.)

  • Set the update interval to 60 seconds:
M000000,25,60
  • Set the GPRS server. The manufacturer example uses the Plaspy server IP and port. This command shows the IP form exactly as provided:
M000000,24,56 54.85.159.138,8888

Note: If the device accepts domain names you may replace the IP with d.plaspy.com, otherwise use the IP as shown.

  • Enable GPRS mode:
M000000,21,2

Default password note: The sample setup uses the device password 000000 as the SMS command prefix. If your device password was changed, replace the password portion accordingly.

Configuration Notes​

  • SMS based configuration is shown in the manufacturer content and is commonly used for initial setup; tools and PC software may also be available from Megastek.
  • Firmware versions and regional hardware variants can change command behavior or available parameters. Confirm commands against your device firmware.
  • Choose UDP or TCP according to your deployment needs; Plaspy accepts both and will detect the protocol automatically.
  • The example update interval of 60 seconds is illustrative; adjust reporting frequency to balance timeliness and data usage.
  • Verify APN, username, and password values with your mobile operator before sending configuration commands.

Why Use Plaspy with This Configuration​

Using the Megastek GVT-510 with Plaspy provides a straightforward path to get the tracker onto a managed fleet or asset monitoring platform. By pointing the device to the shared Plaspy server endpoint and port and ensuring the APN and device ID are correct, organizations can gain reliable visibility and event reporting for vehicles and assets.

To learn more about Plaspy and supported configurations visit https://www.plaspy.com. For the latest device specific setup details, firmware notes, and official Megastek documentation please verify information with the manufacturer at https://www.megastek.com/ as device behavior and configuration methods may change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy