Skip to main content

Meitrack - T333L Configuration

This page describes the public configuration context for using the Meitrack T333L with the Plaspy platform. It collects the core server settings, practical setup guidance, and example SMS configuration commands that are commonly used to point a T333L tracker at Plaspy for real time tracking and telemetry ingestion.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, but exact manufacturer-side setup steps can vary by firmware revision, regional hardware variant, installation type, and the vendor configuration tools you use. The T333L supports SMS-based configuration commands; the example SMS commands below use the sample default device password 0000 as shown in the public manufacturer guidance.

Configuration Overview​

The goal of this configuration process is to prepare the T333L to communicate reliably with Plaspy, confirm connectivity, and enable the device to report positions and telemetry into the Plaspy platform.

  • Configure the device server address and GPRS parameters so the tracker can establish a data session to Plaspy.
  • Set reporting intervals and timezone so positions and events arrive in the desired cadence.
  • Enable event reporting and relevant sensors so TPMS and driving behavior events are passed to Plaspy.
  • Validate network connectivity and confirm the device is visible in Plaspy after configuration.
  • Use SMS commands or the manufacturer tool to apply settings depending on your device access method.

Configuration Overview​

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol and uses the same port for all supported devices

Typical Requirements Before Setup​

  • Device is powered and installed or accessible for configuration at the vehicle or bench.
  • An active cellular SIM with data enabled and the correct APN information available for insertion into the device settings.
  • Ability to send SMS messages to the device if you will use SMS-based configuration commands, or access to the manufacturer configuration tool if using USB or software.
  • The device password (the public example uses 0000 as the default) and knowledge of the device identifier such as IMEI to confirm registration in the platform.
  • Manufacturer documentation and release notes for the specific T333L firmware version to confirm command syntax and supported parameters.

How This Tracker Connects to Plaspy​

When configured, the T333L reports GNSS positions and events to the shared Plaspy server endpoint and port so Plaspy can ingest location, TPMS, sensor, and event data into mapping, alerts, and reports.

  • The tracker sends periodic GNSS position updates to the Plaspy server endpoint on port 8888.
  • TPMS and driving behavior events are transmitted to Plaspy for alerting and aggregation.
  • RS232 connected sensors and external peripherals forward telemetry that can be correlated in Plaspy.
  • Two-way voice or remote listen-in events are logged and visible with other device events.
  • Plaspy detects the device protocol automatically and processes inbound packets regardless of whether the tracker uses UDP or TCP.

Common Configuration Workflow​

  1. Access the official Meitrack configuration method you will use, such as SMS commands or the manufacturer software for your T333L firmware.
  2. Enter the Plaspy server address as d.plaspy.com or use the server IP 54.85.159.138 where the tool or command requires an IP.
  3. Set the server port to 8888. Remember Plaspy uses this same port for all supported devices.
  4. Choose UDP or TCP if the device requires an explicit transport selection; Plaspy can accept either and auto detects the protocol.
  5. Provide the device APN credentials in the GPRS settings using placeholders such as [apn], [apnu], and [apnp] when required by your command or tool.
  6. Apply or save the configuration and restart the device if required by the tracker model or firmware.
  7. Validate that the device reports to Plaspy by confirming the device appears in the platform and that recent position and event messages are received.

Example Configuration Commands​

The T333L can be configured with SMS commands. The following public example commands come from manufacturer guidance and use the sample device password 0000. Keep the commands in the shown order when the order matters. The factory settings command is optional and intended for initial setups or when a reset is required.

  • Optional initial factory reset (use only if you need to restore defaults):
0000,F11
  • Set the GPRS server to Plaspy using the server IP and port and provide APN details
    • Placeholder explanation: [apn] is the mobile network APN. [apnu] and [apnp] are optional APN username and APN password values and may be omitted if not required by the carrier.
0000,A21,2,54.85.159.138,8888,[apn],[apnu],[apnp]

Note: If you prefer to use the domain name instead of the numeric IP and the device accepts hostnames, enter d.plaspy.com in the same position as the IP address when configuring with tools that support DNS names.

  • Set the time zone to UTC 0
0000,B36,0
  • Set the periodic location update interval to 1 minute (manufacturer example)
0000,A12,6,0
  • Set events reporting (manufacturer example to enable default events)
0000,C03,0

Configuration Notes​

  • SMS-based configuration is supported in the public guidance shown above; ensure your SIM allows sending SMS commands if using this method.
  • Firmware variations and hardware revisions can change command syntax or available parameters; always verify commands against the T333L firmware you have installed.
  • Choose UDP or TCP based on network stability and carrier behavior; Plaspy accepts both and auto-detects the protocol, but network performance and NAT handling can influence which transport is preferable in your environment.
  • Ensure APN credentials ([apn], [apnu], [apnp]) are correct for the SIM and carrier; incorrect APN settings will prevent GPRS connections to d.plaspy.com or 54.85.159.138.
  • If you use the factory reset command, treat it as an initial setup step or troubleshooting measure and reapply required server and APN settings afterward.

Why Use Plaspy with This Configuration​

Using the Meitrack T333L with Plaspy centralizes position, TPMS, sensor and event data so fleet operators gain a unified view of vehicle location, driving behavior, and peripheral telemetry. The shared Plaspy server endpoint and automatic protocol detection simplify device onboarding and let you focus on validating coverage, events, and reporting cadence rather than managing per device server differences.

Learn more about Plaspy on the main website https://www.plaspy.com. For the most current device specific configuration methods firmware behavior and manufacturer details verify the latest documentation at the official Meitrack website https://www.meitrack.com/

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy