Skip to main content

Meitrack - T633L Configuration

This page documents the public configuration context for using the Meitrack T633L with Plaspy. It focuses on the shared Plaspy server settings and practical steps you can use to configure the tracker so it reports to Plaspy for real time tracking, fleet telemetry, and event reporting. Use this guidance together with manufacturer documentation and vendor tools for device specific procedures.

Plaspy uses shared server settings and a single port for all supported devices and automatically detects the tracker protocol when the device connects. Exact manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and vendor configuration tools. The example commands below reflect the public SMS configuration sequence provided for the T633L and include placeholders you should replace with your carrier APN details.

Configuration Overview​

This configuration process prepares the T633L to communicate reliably with Plaspy by pointing the device at the Plaspy server and ensuring interval and event reporting are appropriate for fleet use. The objective is to enable secure data flow from the tracker into Plaspy so vehicles and telemetry appear in the platform with minimal delay.

  • Configure the device to report to the Plaspy server endpoint and port so position updates reach Plaspy.
  • Supply the correct cellular APN and optional APN credentials so GPRS data connects.
  • Set reporting intervals and event flags so Plaspy receives the desired telemetry cadence.
  • Validate connectivity and visibility in Plaspy after applying the configuration.
  • Optionally restore factory settings first when preparing a device for a new deployment.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol when the device connects
  • All devices in Plaspy use the same port 8888 for server communication

Typical Requirements Before Setup​

  • A powered and accessible T633L unit installed or connected for configuration.
  • A working cellular SIM card provisioned for data and able to reach carrier APN settings.
  • Knowledge of the carrier APN and any APN username and password required by your SIM.
  • Access to the official manufacturer configuration method such as SMS commands or vendor tools.
  • The device default password if required for commands is 0000 as shown in the public examples.
  • A way to confirm device reporting in Plaspy after configuration, such as an account with Plaspy or support assistance.

How This Tracker Connects to Plaspy​

The T633L is configured to send location fixes and telemetry to the shared Plaspy server endpoint and port so Plaspy ingests position and event data for mapping, alerts, and analytics. Plaspy’s automatic protocol detection removes the need to select a specific protocol in the platform when the device connects.

  • The tracker is pointed to d.plaspy.com or the Plaspy server IP 54.85.159.138 on port 8888.
  • The device uses the carrier APN and GPRS data to establish a connection to Plaspy.
  • Reports and events are sent over UDP or TCP depending on your device selection and network conditions.
  • Plaspy automatically detects the tracker protocol and handles incoming messages for display and processing.
  • Once connected, location, CAN bus telemetry, and configured sensor events become visible in Plaspy for monitoring and reporting.

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or software for the T633L such as SMS commands or the vendor configuration utility.
  2. Enter the Plaspy server address either as the domain d.plaspy.com or as the server IP 54.85.159.138 depending on the device tool you use.
  3. Set the port to 8888 which Plaspy uses for all supported devices.
  4. Choose UDP or TCP if the device requires you to select a transport protocol for server communication.
  5. Enter the carrier APN and optional APN username and password into the device settings if a GPRS server configuration is required.
  6. Apply or save the configuration and restart the device if the tracker requires a reboot to activate settings.
  7. Validate that the device reports to Plaspy by confirming the unit appears and transmits data in your Plaspy account or via platform diagnostics.

Example Configuration Commands​

The public T633L setup can be performed with SMS commands. The sample sequence below uses the device default password 0000. Replace the placeholders and values with your carrier APN and any required credentials.

  • Optional initial factory reset or restore to factory defaults (use only if needed before provisioning):
0000,F11
  • Set the GPRS server to Plaspy using the Plaspy server IP and port. Replace [apn] with your carrier APN. Optionally include APN username [apnu] and APN password [apnp] if required by your SIM.
0000,A21,2,54.85.159.138,8888,[apn]
  • If your setup requires APN username and password include them as follows
0000,A21,2,54.85.159.138,8888,[apn],[apnu],[apnp]
  • Set the device time zone to UTC 0
0000,B36,0
  • Set the GPS upload interval to once every 1 minute
0000,A12,6,0
  • Configure event reporting flags as shown in the public example
0000,C03,0

Notes on placeholders

  • [apn] is the carrier Access Point Name required for GPRS data.
  • [apnu] is the APN username when required by the carrier.
  • [apnp] is the APN password when required by the carrier.
  • The initial factory reset command 0000,F11 is optional and should only be used when preparing a device for a new deployment or when instructed by your installer.

Configuration Notes​

  • Firmware and region variants can change available commands or parameter ordering; always verify command syntax for your device firmware.
  • The T633L supports SMS based configuration as shown, but many vendors also provide configuration tools or over the air management; choose the method appropriate for your deployment.
  • Choose UDP or TCP based on your network environment and any stability considerations; Plaspy accepts either and will detect the protocol automatically.
  • The Plaspy server can be addressed by domain d.plaspy.com or directly by IP 54.85.159.138 on port 8888; using the server IP can help avoid DNS issues in some carrier networks.
  • Keep a record of the device password and authorized configuration methods to avoid locking a device after changes.

Why Use Plaspy with This Configuration​

Integrating the Meitrack T633L with Plaspy provides a practical path to real time vehicle tracking, high precision location reporting, and enriched telemetry from CAN bus and peripheral sensors. Using the shared Plaspy server settings simplifies mass deployments because every device points to the same Plaspy endpoint and port and the platform automatically detects the device protocol once the tracker connects.

To learn more about Plaspy and platform features visit https://www.plaspy.com. For the latest device specific configuration commands, firmware behavior, and official technical references verify information on the Meitrack website https://www.meitrack.com/ as manufacturer procedures and firmware details may change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy