Skip to main content

Navtelekom - ASN SIGNAL S-4752 Configuration

This page describes the public configuration context for using the Navtelekom ASN SIGNAL S-4752 tracker with the Plaspy platform. It focuses on the practical server settings and the typical steps required to point the S-4752 at Plaspy so the device can report GNSS positions, telemetry, and events for fleet and regulatory workflows.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol. Exact manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools such as the NTC Configurator, so follow the official Navtelekom documentation for device specific interfaces and options.

Configuration Overview​

The goal of this configuration is to prepare the S-4752 to send location and telemetry data to Plaspy reliably and to validate connectivity once configured. Configuration aligns the device network settings with Plaspy server endpoints and ensures the tracker is seen and parsed correctly by the platform.

  • Point the ASN SIGNAL S-4752 at the Plaspy server endpoint so GNSS fixes and telemetry are delivered to Plaspy.
  • Configure the transport and port settings on the device to match Plaspy requirements.
  • Verify cellular connectivity, dual SIM behavior, and that the GNSS antenna and power are installed correctly.
  • Use the manufacturer provided configuration tool or approved workflow to save and apply settings.
  • Confirm the device appears in Plaspy and that periodic position and event messages arrive as expected.

Plaspy Server Settings​

Use the following public Plaspy server settings when configuring the ASN SIGNAL S-4752:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol and all devices use the same port

These settings are the shared endpoint values Plaspy expects for device connections. Configure either the domain or the IP and select UDP or TCP as required by the device firmware.

Typical Requirements Before Setup​

  • Physical access to the ASN SIGNAL S-4752 and its wiring to provide stable power and antenna connections.
  • Active cellular SIM cards with data enabled and proper network coverage for LTE Cat.4 connectivity and fallback to older cellular generations as supported.
  • Access to the official Navtelekom configuration tool or method such as the NTC Configurator or the device web/serial interface.
  • Knowledge of the device IMEI or unique identifier used by Plaspy to associate the tracker with your account.
  • Up to date firmware where possible and copies of the relevant Navtelekom user manuals or passport documentation for reference.

How This Tracker Connects to Plaspy​

When configured, the ASN SIGNAL S-4752 sends GNSS fixes, telemetry and event reports over the cellular link to the Plaspy server endpoint and port. Plaspy ingesting that stream allows real time tracking, history playback and alarm handling inside the platform.

  • GNSS position fixes and timestamps transmitted to d.plaspy.com or 54.85.159.138 on port 8888
  • Telemetry and digital input events delivered alongside location messages for monitoring and rule triggers
  • Device status and heartbeat messages to show connectivity state and battery backup events
  • Onboard SD log reconciliation when connectivity resumes so Plaspy can merge stored records with live data
  • Protocol detection by Plaspy so the platform interprets the device messages without manual protocol selection

Common Configuration Workflow​

  1. Open the official Navtelekom configuration method such as the NTC Configurator, serial terminal, or approved manufacturer tool.
  2. Locate the server or remote host settings and enter d.plaspy.com or alternatively enter 54.85.159.138 if IP entry is preferred.
  3. Set the destination port to 8888 as used by Plaspy for all devices.
  4. If the device requires a transport selection choose UDP or TCP according to installer preference or network considerations.
  5. Save or apply the configuration in the manufacturer tool and ensure the settings are written to the device.
  6. Restart the tracker if the tool or device instructions indicate a reboot is required.
  7. Validate connectivity by checking the device appears in Plaspy and that positions and status messages are received.

Example Configuration Commands​

The ASN SIGNAL S-4752 is typically configured using the Navtelekom NTC Configurator or equivalent manufacturer tool. Exact command strings and interfaces vary by firmware and the vendor configuration utility, so there are no universal public commands provided here. Follow Navtelekom documentation or the NTC Configurator UI to enter the Plaspy server domain or IP, set port 8888, choose UDP or TCP, and commit the configuration.

Configuration Notes​

  • Firmware and hardware revisions can change configuration menu names and available fields. Verify the current Navtelekom manual for your device revision.
  • Dual SIM behavior may be configurable in the manufacturer tool; confirm which SIM is used for data and how failover is handled before deployment.
  • Choosing UDP or TCP can affect message delivery characteristics. UDP is commonly used for lower latency telemetry while TCP can help with guaranteed delivery on some networks.
  • Onboard SD logging and the device backup battery help avoid data loss during temporary outages; ensure logging settings match operational needs.
  • Always confirm that the device IMEI or identifier used by Plaspy matches the tracker you are configuring so data is associated with the correct asset.

Why Use Plaspy with This Configuration​

Using the ASN SIGNAL S-4752 with Plaspy provides fleets and operators with continuous GNSS tracking, telemetry capture and event reporting in a centralized platform. The S-4752 hardware features such as GLONASS/GPS positioning, LTE connectivity, dual SIM redundancy, and robust I O support make it well suited to deliver the raw data that Plaspy ingests for dashboards, geofencing, compliance and anti-theft workflows.

Learn more about Plaspy on https://www.plaspy.com. Device specific configuration methods, firmware behavior and manufacturer instructions can change over time, so verify the latest setup details and manuals with Navtelekom at https://www.navtelecom.ru/ before large deployments.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy