Skip to main content

Navtelekom - СИГНАЛ S-2652 Configuration

This page documents the public configuration context for using the Navtelekom СИГНАЛ S-2652 tracker with the Plaspy platform. It summarizes the shared Plaspy server settings you will enter on the device or in the manufacturer configuration tool, and provides practical workflow guidance to prepare the tracker for real-time reporting and data transfer to Plaspy.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when data arrives at its endpoint. Exact manufacturer-side steps for the S-2652 can vary by firmware version, hardware revision, installation type, and vendor tools such as NTC Configurator or DRC remote management. Use this guide to align the S-2652 with Plaspy, and refer to the manufacturer documentation for device-specific procedures.

Configuration Overview​

Preparing the СИГНАЛ S-2652 for Plaspy focuses on configuring the tracker to report location and telemetry to Plaspy's shared server endpoint and port, validating connectivity, and ensuring the device appears in the Plaspy platform for monitoring and reporting.

  • Set the device to report to Plaspy using the server domain or server IP and the shared Plaspy port.
  • Choose the transport mode required by your device firmware, either UDP or TCP.
  • Save and apply configuration via the manufacturer tool or SMS/remote management as supported.
  • Validate the device reports correctly to Plaspy and that logged records (microSD) upload after connectivity restoration.
  • Confirm inputs, outputs and CAN mappings are visible and functioning in Plaspy for event reporting and control.

Plaspy Server Settings​

Use the following public Plaspy connection values when configuring the СИГНАЛ S-2652:

  • server domain d.plaspy.com
  • server IP 54.85.159.138
  • port 8888
  • transport support for UDP or TCP
  • automatic protocol detection in Plaspy

Note that all devices in Plaspy use the same port and the platform will automatically detect the tracker protocol when the device begins sending data.

Typical Requirements Before Setup​

  • A powered S-2652 with working GNSS antenna and cellular modem active.
  • Valid SIM card(s) inserted for cellular connectivity and, where applicable, mobile data enabled.
  • Access to the official Navtelekom configuration method such as NTC Configurator, SMS commands, or DRC remote management tools.
  • A microSD card installed if you rely on onboard logging during network outages.
  • Knowledge of the device firmware version and any vendor-specific transport or protocol options.
  • Physical access to device wiring and inputs/outputs if you must verify ignition, immobilizer, or sensor connections.

How This Tracker Connects to Plaspy​

The СИГНАЛ S-2652 sends GNSS position and telemetry through its cellular modem to the Plaspy server endpoint. Plaspy ingests the incoming telematics stream, correlates input and CAN data, and presents real-time tracking, alerts, and historical logs in the platform.

  • The device reports to the shared Plaspy server endpoint using d.plaspy.com or the server IP 54.85.159.138.
  • Data is sent to port 8888 on Plaspy using either UDP or TCP depending on device configuration.
  • Plaspy automatically detects the tracker protocol so you do not need to select a protocol in the platform.
  • Onboard microSD logging preserves records during temporary network outages and those records can be forwarded to Plaspy when connectivity resumes.
  • Inputs, outputs and CAN-based telemetry appear in Plaspy for event-driven alerts and operational monitoring.

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or software (for example NTC Configurator or DRC) or prepare the SMS/remote method recommended by Navtelekom.
  2. Enter the Plaspy server address by specifying d.plaspy.com or alternatively 54.85.159.138 in the device server field.
  3. Set the device port to 8888, matching Plaspy's shared port for all devices.
  4. Choose UDP or TCP if the device requires a transport selection in the configuration tool.
  5. Apply or save the configuration and push settings to the device using the manufacturer tool or via the supported remote channel.
  6. Restart the device if required by the firmware or instructed by the configurator.
  7. Validate that the device reports to Plaspy by confirming the tracker appears in the Plaspy interface and that position and event updates are received.

Example Configuration Commands​

This model configuration page does not include manufacturer SMS or command-line strings. Exact configuration commands and the method of delivery depend on the Navtelekom firmware and the configuration tool in use. Use the official Navtelekom configurator or the device SMS command reference to set the server to d.plaspy.com or 54.85.159.138, set port 8888, and select UDP or TCP where required. If you prefer, configure via the NTC Configurator or DRC remote management following the manufacturer's command formats.

Configuration Notes​

  • The S-2652 supports remote configuration via manufacturer tools; follow NTC Configurator or DRC guidance for precise menus and command formats.
  • Firmware revisions and hardware revisions can change menu names and transport options; confirm the exact steps for your firmware version.
  • Choose UDP or TCP according to device firmware support and network reliability; Plaspy accepts either transport on port 8888 and will detect the protocol automatically.
  • Because the model is discontinued, verify that remote management tools and firmware updates are available for your installed units before deployment.
  • Use microSD logging to capture data during connectivity loss and confirm proper upload behavior to Plaspy after reconnection.

Why Use Plaspy with This Configuration​

Integrating the Navtelekom СИГНАЛ S-2652 with Plaspy gives organizations a straightforward path to capture real-time location, telemetry and input/output events from a rugged on-board tracker. Plaspy's shared server endpoint and automatic protocol detection simplify the device-side configuration, enabling reliable position reporting, event alerts and historical reporting for fleet operations and compliance workflows.

To learn more about Plaspy and how it works with vehicle telematics devices visit https://www.plaspy.com. For the most current device-specific configuration methods, firmware behavior and manufacturer documents for the S-2652 consult the official Navtelekom website https://www.navtelecom.ru/ which provides the authoritative technical references and replacement guidance.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy