Skip to main content

Navtelekom - СИГНАЛ S-4651 (4G) Configuration

This page documents the public configuration context for using the Navtelekom СИГНАЛ S-4651 (4G) tracker with the Plaspy platform. It consolidates the Plaspy server settings you need to enter on the device or in the manufacturer configuration tool and explains the practical steps to validate that the tracker is reporting to Plaspy. The information here focuses on the publicly available integration details and typical workflow for connecting this model to Plaspy.

Plaspy uses shared server settings across supported trackers and automatically detects the tracker protocol, so you will use the same port and endpoint settings that apply to all Plaspy devices. Exact manufacturer-side steps can vary by firmware version, hardware revision, installation type, and the configuration tools you use, so always confirm device-specific procedures with Navtelekom documentation when needed.

Configuration Overview​

This configuration prepares the SIGNAL S-4651 to send GNSS, I/O events, and telemetry to Plaspy so fleet managers can monitor vehicles in real time. The goal is to point the tracker at the Plaspy endpoint, choose the appropriate transport, and verify that data is received by the platform.

  • Enter the Plaspy server endpoint and transport in the device configuration tool or SMS/DRC method supported by the device.
  • Set the port used by Plaspy so the tracker’s outgoing data reaches the platform.
  • Confirm network connectivity and SIM readiness for cellular data transmission.
  • Validate that the device appears online in Plaspy and that position and event reports are visible.
  • Optionally enable local logging or remote firmware updates per installer practice to support maintenance.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol

These values are the public Plaspy settings to use when configuring the SIGNAL S-4651 for real-time reporting.

Typical Requirements Before Setup​

  • Ensure the SIGNAL S-4651 is powered and correctly installed with required antennas and wiring for vehicle use.
  • Have an active cellular data SIM or dual SIM cards inserted and verified for data connectivity.
  • Access to the official Navtelekom configuration method such as NTC Configurator or the device pairing tool used by your installer.
  • Firmware version and model documentation available from Navtelekom to confirm feature support and configuration options.
  • A microSD card inserted if you plan to use local data logging or offline storage during intermittent connectivity.
  • Administrative access to Plaspy account settings to confirm device visibility after configuration.

How This Tracker Connects to Plaspy​

The SIGNAL S-4651 reports location, I/O events, and telemetry over cellular networks to the shared Plaspy server endpoint and port. Plaspy’s ingestion automatically handles the supported tracker protocol so the platform can interpret messages and display device status.

  • The device is configured to send data to d.plaspy.com (or to 54.85.159.138) on port 8888.
  • You may select UDP or TCP transport on the tracker if a transport choice is required by the device.
  • Plaspy automatically detects the tracker protocol once data reaches the platform endpoint.
  • Reported data typically includes GNSS coordinates, digital/analog input events, and telemetry captured via supported interfaces.
  • Once connected, the device becomes visible in Plaspy for live tracking, alerts, and historical playback.

Common Configuration Workflow​

  1. Access the official Navtelekom configuration method or software used for this model such as the NTC Configurator or the manufacturer’s configuration interface.
  2. In the server or APN configuration section enter the Plaspy endpoint as d.plaspy.com or, if required, the server IP 54.85.159.138.
  3. Set the server port to 8888, noting that Plaspy uses the same port for all supported devices.
  4. If the device requires a transport selection, choose UDP or TCP according to your network and installer preference.
  5. Apply or save the configuration changes in the device tool and confirm that settings are written to the device.
  6. Restart the device if the manufacturer tool or install instructions require a reboot to apply network settings.
  7. Validate that the device reports to Plaspy by checking the device status and recent position updates on the Plaspy platform.

Example Configuration Commands​

No public device-specific command strings were provided with this guide. Exact configuration commands and SMS strings vary by Navtelekom firmware and the configuration tool used. Use the official Navtelekom configurator or the device’s documented management interface to set:

  • server hostname or IP to d.plaspy.com or 54.85.159.138
  • server port to 8888
  • transport to UDP or TCP where applicable

If you have manufacturer command examples or SMS configuration strings from Navtelekom documentation, include them in your installer notes and preserve placeholders such as APN credentials when entering network settings.

Configuration Notes​

  • The SIGNAL S-4651 model is archived by Navtelekom; confirm the correct firmware and configuration tool that match your unit before making changes.
  • Dual SIM failover should be configured per installer practice to maintain continuous connectivity; verify SIM priority rules in the device manual.
  • Choosing TCP versus UDP may affect delivery guarantees and network behavior; select the transport that aligns with your connectivity and firewall rules.
  • Plaspy uses the same port (8888) for all devices and will automatically detect the device protocol when messages arrive at d.plaspy.com.
  • Keep manufacturer documentation handy for any model-specific steps such as remote firmware update procedures or special I/O mapping.

Why Use Plaspy with This Configuration​

Connecting the Navtelekom СИГНАЛ S-4651 (4G) to Plaspy gives fleet operators a standardized endpoint for collecting vehicle positions, I/O events, and telemetry across a mixed device fleet. The device’s multi-network cellular support, dual SIM capability, and rich I/O set make it a practical choice for operators who need continuous visibility and flexible telemetry integration with a single platform.

To learn more about Plaspy and supported integrations visit https://www.plaspy.com. Device-specific configuration methods, firmware behavior, and manufacturer details can change over time, so verify the latest information and tools on the official Navtelekom site https://www.navtelecom.ru/.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy