Skip to main content

Navtelekom - СМАРТ S-2333A HIT Configuration

This page documents the public configuration context for using the Navtelekom СМАРТ S-2333A HIT with Plaspy. It summarizes the practical server settings, required prechecks, and a typical workflow integrators use to prepare this legacy GLONASS/GPS vehicle tracker for real-time monitoring on the Plaspy platform. The guidance below is based on published device capabilities and public Plaspy ingestion information.

Plaspy uses a shared set of server settings across supported devices and automatically detects the tracker protocol, while the specific manufacturer-side steps may vary by firmware version, hardware revision, installation type, and the configuration tools provided by Navtelekom such as the NTC Configurator utility. Always consult the device manual and the NTC Configurator documentation for device-specific UI screens or SMS command formats when available.

Configuration Overview​

To integrate the СМАРТ S-2333A HIT with Plaspy you prepare the device to send its GNSS and telemetry data to Plaspy ingestion endpoints and then verify connectivity and reporting in the Plaspy platform. The Plaspy server endpoint and port are consistent across devices and Plaspy will automatically detect the tracker protocol once the device reports in.

  • Configure the tracker to report to the Plaspy server endpoint so position and event packets are routed correctly.
  • Select the appropriate transport mode (UDP or TCP) if the device requires a choice and set the common Plaspy port.
  • Use the manufacturer configuration method such as the NTC Configurator or approved SMS commands to apply settings.
  • Apply and save changes, then verify the device reaches the Plaspy server and appears in the platform.
  • Validate event reporting from digital inputs, analog sensors, and RS-485 or 1-Wire peripherals as applicable.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol after the device begins reporting

These values are the public Plaspy ingestion endpoint and must be entered into the tracker configuration using the manufacturer tool or methods supported by the device.

Typical Requirements Before Setup​

  • Access to the official Navtelekom documentation for the СМАРТ S-2333A HIT and the NTC Configurator utility when required
  • A charged device battery and or vehicle power connection to ensure the unit can boot and register on the network
  • A working SIM card provisioned for data and basic connectivity compatible with the device 2G modem and local carriers
  • The device IMEI or unique identifier to register or identify the unit in Plaspy after it reports
  • A PC or interface cable if using local configuration software, or access to the SMS command set if configuring remotely
  • Confirmation of compatible firmware or NTC Configurator version that supports configuration options for server, port, and transport

How This Tracker Connects to Plaspy​

The СМАРТ S-2333A HIT transmits GNSS position and telemetry from its integrated GLONASS/GPS receiver over the device 2G GSM modem to Plaspy. When configured to use the Plaspy endpoint, the tracker sends standard telematics messages so Plaspy can ingest location, inputs, and peripheral sensor data.

  • The tracker is configured to report to the shared Plaspy server endpoint and port d.plaspy.com or 54.85.159.138 on port 8888
  • Choose UDP or TCP as the transport on the device if prompted; both transports are accepted by Plaspy on port 8888
  • Plaspy automatically detects the tracker protocol after the device connects and begins sending data
  • Digital inputs, analog readings, and pulse counters are forwarded to Plaspy for event and telemetry processing
  • RS-485 and 1-Wire connected sensors report through the tracker into Plaspy when supported by the device firmware and sensor setup

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or software such as the NTC Configurator utility or the vendor recommended SMS command set.
  2. Identify the target device by IMEI or other device identifier within the configuration tool.
  3. Enter the Plaspy server address using either the domain d.plaspy.com or the server IP 54.85.159.138 as allowed by the tool.
  4. Set the device port to 8888.
  5. Choose UDP or TCP if the device configuration requires a transport selection.
  6. Apply or save the configuration changes in the manufacturer tool and upload them to the device.
  7. Restart or power cycle the device if required by the device firmware to activate the new network settings.
  8. Validate that the device reports to Plaspy and appears in the platform, confirming that the automatic protocol detection has completed and telemetry is visible.

Example Configuration Commands​

The exact configuration commands and steps vary by Navtelekom firmware release and the NTC Configurator version. Some integrators use the NTC Configurator desktop utility to set server, port and transport, while others may use an SMS based command set if the firmware supports it. Because command syntax is manufacturer specific and can change between firmware versions, consult the Navtelekom user manual or NTC Configurator help for precise command formats and examples for the СМАРТ S-2333A HIT.

If you have access to manufacturer-provided command examples, follow the documented order to set server, set port, select transport, and save or reboot. Preserve any placeholders used by the manufacturer such as [apn] or similar and replace them with your carrier APN values when required.

Configuration Notes​

  • Firmware version matters: different firmware builds and NTC Configurator versions can expose different menus or SMS syntax for server and transport settings.
  • TCP versus UDP: choose the transport that matches your deployment needs; Plaspy accepts both on port 8888 and will detect the protocol.
  • Use either d.plaspy.com or 54.85.159.138 when entering server information according to what the configuration tool accepts.
  • Keep the device IMEI and any device identifiers handy for registration and verification in Plaspy after configuration.
  • Review the Navtelekom product passport and user manual for any device-specific configuration steps or hardware revision notes.

Why Use Plaspy with This Configuration​

Using the Navtelekom СМАРТ S-2333A HIT with Plaspy brings legacy GLONASS/GPS tracking hardware into a modern monitoring workflow. For fleets and asset owners who maintain older hardware, this configuration enables live position reporting, event-driven alerts from digital inputs, and expanded telemetry from analog and peripheral sensors, all consolidated into the Plaspy platform for operational oversight.

To learn more about Plaspy and platform features visit https://www.plaspy.com. For the most current device specific setup instructions, firmware notes, and manufacturer documentation verify details on the Navtelekom website https://www.navtelecom.ru/ as hardware revisions and firmware behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy