Skip to main content

Navtelekom - SMART S-2410 Configuration

This page documents the public configuration context for using the Navtelekom SMART S-2410 tracker with the Plaspy platform. It compiles the practical server settings and workflow notes you need to point the device to Plaspy and validate basic connectivity. Use this guide as a reference for integrating the SMART S-2410 into Plaspy for position and event telemetry.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, but exact manufacturer-side steps can vary by firmware version, hardware revision, installation type, or the configuration tool you choose. Follow this guide together with Navtelekom installation manuals and the manufacturer tools such as NTC Configurator or the DRC platform to complete commissioning and ongoing maintenance.

Configuration Overview​

The goal of configuration is to prepare the SMART S-2410 to communicate reliably with Plaspy and to validate that position and event reports are visible in the platform. Typical configuration focuses on network addresses, transport selection, and ensuring device inputs and outputs are mapped correctly for your monitoring needs.

  • Point the device to the Plaspy server endpoint so telemetry is routed to the platform.
  • Select the transport mode required by your installation, UDP or TCP, and configure it on the device if needed.
  • Ensure the device has a valid cellular connection and correct SIM provisioning for 2G telemetry.
  • Use local Bluetooth commissioning or the manufacturer configuration tool to apply and verify settings.
  • Validate that location updates and input events appear in Plaspy after configuration.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol so the platform accepts compatible telemetry formats

These values are the shared Plaspy endpoint settings used by all devices on the platform. Configure the SMART S-2410 to report to either the domain or the IP and to use port 8888.

Typical Requirements Before Setup​

  • Vehicle power available and wiring connected according to Navtelekom documentation
  • A valid 2G SIM card provisioned for data if cellular telemetry is required
  • Access to local configuration methods such as Bluetooth 4.0 commissioning or the NTC Configurator/DRC tools
  • Device firmware and wiring documentation from Navtelekom to confirm input and output mapping
  • Basic network reachability to the Plaspy server from the installation region
  • Credentials or access needed to the manufacturer's configuration software where applicable

How This Tracker Connects to Plaspy​

The SMART S-2410 transmits GNSS position and discrete/analog input events over its integrated 2G modem to the Plaspy endpoint. Configuration ensures telemetry is sent to the shared Plaspy server address and port so the platform can ingest and display device data.

  • The device is set to report location and event messages to d.plaspy.com or 54.85.159.138
  • Telemetry is sent on port 8888 using UDP or TCP depending on the configured transport
  • Plaspy automatically detects the tracker protocol so standard Navtelekom message formats are accepted
  • Inputs such as ignition, door, and alarm are reported as events and visible in Plaspy dashboards
  • Control output actions can be used with Plaspy workflows for remote actuation where required

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or software such as NTC Configurator, local Bluetooth tool, or DRC remote management platform.
  2. Enter the Plaspy server address either as the domain d.plaspy.com or as the server IP 54.85.159.138 in the device network/server settings.
  3. Set the device reporting port to 8888.
  4. Choose UDP or TCP in the transport or protocol selection if the device requires you to pick a transport.
  5. Apply or save the configuration in the manufacturer tool or via local Bluetooth commissioning.
  6. Restart the device if the tool or firmware requires a reboot for settings to take effect.
  7. Validate that the device reports to Plaspy by confirming that location updates and input events appear in the platform.

Follow the manufacturer tool prompts and the device status indicators while performing each step. If using remote management (DRC), confirm that the pushed configuration was accepted by the device after the remote session completes.

Example Configuration Commands​

The SMART S-2410 model configuration commands vary by the manufacturer tool, firmware version, and whether you use Bluetooth, SMS, or a desktop configurator. Because model specific commands are provided and maintained by Navtelekom, exact command syntax is not included here. Use one of the manufacturer supported methods listed below to apply the Plaspy server settings:

  • NTC Configurator or DRC remote management platform for GUI based configuration
  • Local Bluetooth 4.0 commissioning tool on a smartphone or tablet for on site setup

When using these tools, enter d.plaspy.com or 54.85.159.138 as the server and set port 8888. Select UDP or TCP if the device requires a transport selection. For command line or SMS based setups consult the Navtelekom configuration guide for the precise message format and placeholders.

Configuration Notes​

  • Firmware and hardware revisions may change field names, menus, or command formats. Confirm exact steps with the current Navtelekom documentation.
  • Choose UDP for lower overhead and broader legacy compatibility, or TCP if your installation requires a connection oriented transport; Plaspy accepts either on port 8888.
  • Bluetooth commissioning is useful for on vehicle setup, but remote tools such as DRC are recommended for fleet scale deployments.
  • Because the SMART S-2410 uses a 2G modem, verify 2G coverage in your deployment area before committing to large scale installations.
  • Plaspy uses the same port for all devices and automatically detects tracker protocol, which simplifies multi-vendor deployments.

Why Use Plaspy with This Configuration​

Configuring the SMART S-2410 to report to Plaspy provides straightforward real time location and event visibility for fleets and asset tracking. The tracker’s discrete and analog inputs combined with reliable GNSS and a simple control output make it suitable for basic telemetry, ignition monitoring, and anti-theft workflows when 2G is available.

For step by step manufacturer commands and the latest firmware behavior, refer to Navtelekom documentation. To learn more about Plaspy and how the platform ingests and presents device telemetry, visit https://www.plaspy.com. Device specific configuration methods, firmware behavior, and manufacturer details can change over time, so always verify the current setup instructions and technical specifications on the official Navtelekom website https://www.navtelecom.ru/.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy