Skip to main content

Navtelekom - SMART S-2420 Configuration

This page documents the public configuration context for using the Navtelekom SMART S-2420 with Plaspy. It summarizes the shared server settings required by Plaspy, explains what to prepare before integration, and describes the practical workflow for pointing the device at Plaspy so the tracker can report location, telemetry, and I O state to the platform. The guidance below uses information publicly available for the SMART S-2420 and the standard Plaspy server settings.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while exact manufacturer-side setup steps can vary by firmware, hardware revision, installation type, and vendor tools. Use the manufacturer configuration method provided by Navtelekom for the SMART S-2420, and follow the Plaspy server values listed here to ensure reliable connectivity.

Configuration Overview​

The goal of this configuration is to prepare the SMART S-2420 to deliver location and basic telemetry to Plaspy so the device appears in your Plaspy account and generates the expected events and reports. This typically means configuring the device to send uplink packets to the Plaspy server endpoint and confirming that messages arrive correctly.

  • Configure the tracker to report to the Plaspy server endpoint and port so Plaspy receives position and telemetry packets.
  • Validate mobile network connectivity and SIM functionality for the S-2420 2G modem before commissioning.
  • Use the Navtelekom configuration tool or Bluetooth local setup to enter the Plaspy server settings.
  • Save and apply configuration then confirm the device is visible in Plaspy and reporting GPS and I O states.
  • If required, restart the device after applying settings to start fresh network sessions.

Plaspy Server Settings​

Use the following public Plaspy server values when configuring the SMART S-2420. Plaspy uses the same port for all supported devices and automatically detects the tracker protocol.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol so devices can use either UDP or TCP as supported

Typical Requirements Before Setup​

  • Vehicle power available and connected since the SMART S-2420 has no internal battery and is intended for permanent installation.
  • A functioning single SIM with regional 2G service where the device will operate, because the S-2420 uses a 2G GSM modem.
  • Access to the official Navtelekom configuration method for the S-2420 such as the Bluetooth local configuration tool or vendor software.
  • Physical access to the device to verify wiring for inputs and outputs and to perform a restart if needed.
  • A Plaspy account and basic familiarity with the platform so you can confirm the device appears and reports after setup.

How This Tracker Connects to Plaspy​

The SMART S-2420 sends periodic position and telemetry packets over its 2G uplink to the Plaspy server endpoint and port. Once the device is pointed at Plaspy and network connectivity is present, Plaspy receives location fixes, digital input states, and other basic telemetry for display and reporting.

  • The tracker transmits GPS and GLONASS fixes via the 2G modem to the Plaspy server endpoint.
  • Digital input and output events are reported as telemetry and can be mapped in Plaspy for alerts and logging.
  • The device uses the shared Plaspy server address and port so messages are routed to the Plaspy platform.
  • Plaspy’s automatic protocol detection allows the tracker to use UDP or TCP as appropriate for the device and network.
  • Bluetooth 4.0 on the S-2420 is available for local configuration and diagnostics during installation.

Common Configuration Workflow​

  1. Access the official Navtelekom configuration method for the SMART S-2420 (Bluetooth local tool or vendor configuration software).
  2. Enter the Plaspy server address using either d.plaspy.com or the IP 54.85.159.138 into the device server field.
  3. Set the server port to 8888 as all Plaspy devices use the same port.
  4. Choose the transport protocol UDP or TCP if the device requires a transport selection.
  5. Apply or save the configuration settings in the Navtelekom tool.
  6. Restart the device if the configuration tool or documentation recommends a reboot to establish fresh network sessions.
  7. Validate that the device reports to Plaspy by confirming the device appears in your Plaspy account and that position and telemetry updates are received.

Example Configuration Commands​

The SMART S-2420 is typically configured using Navtelekom’s local Bluetooth configuration tool or manufacturer software. Exact command formats or SMS strings vary by firmware and vendor utility. Because available public commands differ by firmware and revision for archived models, consult Navtelekom documentation or use the provided Bluetooth tool to enter the server d.plaspy.com or 54.85.159.138 and port 8888, and choose UDP or TCP where required.

If you have specific published command strings from Navtelekom for this model, apply them in the order the manufacturer documentation prescribes and preserve any placeholders such as APN values as provided. For verification, check device response logs in the configuration tool and then confirm messages arrive at Plaspy.

Configuration Notes​

  • The SMART S-2420 is an archived model so firmware and command sets may differ across units; check the Navtelekom downloads or DRC portal for the correct firmware documentation before changing settings.
  • Because the device uses 2G, verify cellular network availability in your region prior to deployment.
  • Choosing UDP versus TCP can affect how the device handles retries and connections; Plaspy supports both and auto detects the protocol.
  • Use the Navtelekom Bluetooth configuration method for local setup to avoid SMS command complexity when possible.
  • Always save and, if recommended, restart the device after applying the Plaspy server settings to ensure the change takes effect.

Why Use Plaspy with This Configuration​

Using the SMART S-2420 with Plaspy provides a straightforward path to vehicle visibility, basic telemetry collection, and simple remote control workflows such as immobilization via control outputs. For organizations needing low cost, entry level tracking with GLONASS/GPS positioning and digital I O reporting, pairing the S-2420 with Plaspy enables centralized monitoring and event reporting in a single platform.

To learn more about Plaspy and supported device configuration options visit https://www.plaspy.com. For the most current device specific setup instructions, firmware files, and official manuals for the SMART S-2420 consult Navtelekom at https://www.navtelecom.ru/ since manufacturer specifications and firmware behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy