Skip to main content

Navtelekom - SMART S-2435 MAX Configuration

This page documents the public configuration context for using the Navtelekom SMART S-2435 MAX with Plaspy. It summarizes the practical server settings and workflow required to point the device to Plaspy, and it uses the tracker description as the factual grounding for what the device provides: GLONASS/GPS positioning, dual SIM 2G modem with internal GSM antenna, internal GNSS/GPS antenna, a backup battery, and multiple I/O options for telemetry integration.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, but manufacturer-side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools. Use this guide to understand the required Plaspy server values and the typical sequence of actions; always confirm device-specific commands and firmware behavior with the official Navtelekom documentation.

Configuration Overview​

This configuration process prepares the SMART S-2435 MAX to send GNSS positions and telemetry to the Plaspy platform and validates that the device appears and reports correctly in the Plaspy system.

  • Configure the tracker to report to the Plaspy server endpoint so data is received by Plaspy in real time.
  • Select the transport (UDP or TCP) and ensure the device uses the Plaspy shared port so the platform can accept incoming data.
  • Save and apply the device configuration using the official Navtelekom configuration tool or supported local methods.
  • Restart or power-cycle the device if required, then validate connectivity and reporting in Plaspy.
  • Verify telemetry channels such as universal inputs, outputs, and Bluetooth sensors are enabled and visible in Plaspy.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP depending on device selection
  • Plaspy automatically detects the tracker protocol and uses the same port for all supported devices

Typical Requirements Before Setup​

  • A powered and accessible SMART S-2435 MAX installed or temporarily connected for configuration.
  • Active SIM card(s) inserted if using the device cellular link; ensure GSM coverage for 2G service in your area.
  • Access to the official Navtelekom configuration method or software such as the manufacturer configurator or supported local tools.
  • A PC, smartphone, or Bluetooth tool if local Bluetooth configuration is required for parameterization.
  • Knowledge of the device firmware version and any vendor-specific configurator guidance applicable to your hardware revision.

How This Tracker Connects to Plaspy​

The SMART S-2435 MAX transmits GNSS positions and telemetry over its cellular link to the Plaspy server endpoint and port. Once directed to Plaspy, the platform updates vehicle locations, processes telemetry inputs, and stores history for reporting and alerts.

  • Real-time GNSS position updates and route history transmitted to the Plaspy server endpoint (d.plaspy.com / 54.85.159.138) on port 8888.
  • Telemetry and event reporting from universal inputs and CAN/serial interfaces that are forwarded to Plaspy for monitoring and rules processing.
  • Control output events and remote actions reflected in Plaspy workflows when triggered by platform rules.
  • Local Bluetooth connectivity for on-site parameterization and short-range sensor reads, with resulting telemetry forwarded to Plaspy via the device cellular link.
  • Plaspy automatically detects the device protocol so the tracker can use standard Plaspy port settings without custom server differentiation.

Common Configuration Workflow​

  1. Access the official Navtelekom configuration method or software (for example, the manufacturer configurator or approved parameterization tool).
  2. Ensure SIM cards are installed and the device has power and cellular signal for 2G GSM connectivity.
  3. Enter the Plaspy server address either as the domain d.plaspy.com or the server IP 54.85.159.138 in the device server/host field.
  4. Set the device port to 8888 and, if required by the device, choose UDP or TCP as the transport.
  5. Apply or save the configuration in the manufacturer tool and upload it to the device.
  6. Restart or power-cycle the SMART S-2435 MAX if the firmware requires a reboot to apply network settings.
  7. Validate that the device reports to Plaspy by checking device activity and incoming positions on the Plaspy platform.

Example Configuration Commands​

The exact configuration commands and the method to send them depend on the Navtelekom configurator tool or the device firmware. Some installers use a GUI configurator, others use local Bluetooth/serial tools or SMS strings where supported. When using the manufacturer tool, enter the Plaspy server values as shown below in the corresponding server host and port fields:

  • Server host: d.plaspy.com or 54.85.159.138
  • Server port: 8888
  • Transport: UDP or TCP

Because configuration commands vary by firmware and vendor tool, consult the Navtelekom configurator documentation for the precise command syntax and upload procedure for your device. Plaspy will automatically detect the tracker protocol once the device reports to the configured endpoint and port.

Configuration Notes​

  • Firmware differences and hardware revisions can change the exact parameter names, available transports, or the UI layout in the manufacturer tool; always confirm parameters for your firmware version.
  • Choose UDP or TCP based on your installation and the Navtelekom tool prompts; Plaspy accepts either transport on port 8888 and performs protocol detection automatically.
  • All Plaspy devices use the same listening port so you do not need unique ports per device; use 8888 as the standard port.
  • Local Bluetooth configuration is supported by the device for on-site parameterization; follow the Navtelekom Bluetooth setup steps when available.
  • Verify SIM and cellular connectivity before finalizing configuration to avoid false negatives when validating reporting in Plaspy.

Why Use Plaspy with This Configuration​

Using the SMART S-2435 MAX with Plaspy provides a practical path to integrate vehicle and asset telemetry into a central platform for live maps, route history, and event-driven alerts. The device’s dual SIM 2G modem, multiple I/O options, and Bluetooth parameterization capabilities make it well suited for fleet monitoring, anti-theft workflows, and telemetry-driven maintenance when connected to Plaspy.

Learn more about Plaspy and how it can visualize and manage device data on the Plaspy website https://www.plaspy.com. Device specific configuration methods, firmware behavior, and manufacturer details can change over time, so verify the latest setup information and firmware notes with the manufacturer at https://www.navtelecom.ru/.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy