Skip to main content

Navtelekom - СМАРТ S-4535 Configuration

This page covers the public configuration context for using the Navtelekom СМАРТ S-4535 tracker with the Plaspy platform. It focuses on the practical, shareable settings and workflow required to prepare the device to communicate with Plaspy for live tracking, telemetry forwarding, and event reporting. Details here are based on the tracker description and publicly available integration practices rather than internal or proprietary configuration flows.

Plaspy uses shared server settings across supported devices and automatically detects device protocols, while exact manufacturer-side setup steps can vary by firmware version, hardware revision, installation type, and vendor configuration tools. Use the guidance below to prepare the device for connection to Plaspy, and consult Navtelekom materials for device specific configuration and tools such as the DRC remote management system or the NTC Configurator.

Configuration Overview​

Preparing the СМАРТ S-4535 for Plaspy integration means pointing the device at the Plaspy server endpoint, verifying connectivity, and ensuring the device is reporting the expected telemetry channels. The tracker’s 4G modem and dual SIM capability provide redundant communications to reduce data gaps, and on-device logic can reduce server load by filtering and generating events locally.

  • Configure the device to send tracking data to the Plaspy server endpoint so that position and telemetry appear in Plaspy dashboards.
  • Verify network connectivity and SIM data availability to ensure the device can reach the Plaspy server.
  • Select the transport protocol the device supports and point it to the shared Plaspy port used by all devices.
  • Save and apply the configuration using Navtelekom tools or SMS commands as provided by the manufacturer.
  • Confirm that the tracker reports successfully to Plaspy at the configured server and port.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP — device may be configured to use either UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol when the device connects

These are the public Plaspy endpoint details to use when configuring the SMART S-4535 so the device is routed into Plaspy for processing.

Typical Requirements Before Setup​

  • Device powered and installed with an active SIM card that has a data plan enabled for IP connectivity
  • Physical access to the tracker or remote access via Navtelekom remote management tools such as DRC if available
  • Manufacturer configuration tool or procedure such as NTC Configurator or documented SMS commands
  • Knowledge of which transport to use UDP or TCP depending on installation preferences or constraints
  • A Plaspy account or access to the Plaspy instance where the device will be monitored
  • Basic verification tools such as a mobile device for Bluetooth configuration or a terminal to confirm device responses when applicable

How This Tracker Connects to Plaspy​

The СМАРТ S-4535 uses its cellular modem to open a data session and send location, CAN bus telemetry, and input/output events to the Plaspy endpoint. Once configured to target the shared Plaspy server and port, Plaspy maps incoming telemetry into dashboards and alerts while automatically recognizing the device protocol.

  • Device sends periodic position and telemetry packets to d.plaspy.com or directly to 54.85.159.138 on port 8888
  • Communications may use UDP or TCP depending on the transport selected during configuration
  • Plaspy automatically detects the tracker protocol and processes the incoming payloads
  • Onboard event logic can reduce noise by sending only relevant events to the Plaspy server
  • Successful configuration results in live visibility, event reporting, and telemetry forwarding in Plaspy

Common Configuration Workflow​

  1. Access the official Navtelekom configuration method or software such as the NTC Configurator or the DRC remote control system, or use the manufacturer documented SMS commands if applicable.
  2. In the manufacturer tool, enter the Plaspy server by domain d.plaspy.com or by server IP 54.85.159.138.
  3. Set the device reporting port to 8888 which is the shared Plaspy port used for all devices.
  4. If the device requires a transport selection, choose UDP or TCP based on your requirements and network stability.
  5. Apply or save the configuration in the device tool and confirm changes were written to the device.
  6. Restart the tracker if required by the device firmware or the manufacturer instructions so the new settings take effect.
  7. Validate that the device reports to Plaspy by checking device activity in the Plaspy platform or by observing server-side acknowledgements if provided.

Example Configuration Commands​

The exact configuration commands and syntax for the СМАРТ S-4535 vary by manufacturer tool and firmware. For this model Navtelekom provides configuration via the NTC Configurator or the DRC remote system and may also support SMS command provisioning. When you use those tools, supply the Plaspy server details d.plaspy.com or 54.85.159.138 and port 8888 and select UDP or TCP as required.

If you have access to manufacturer SMS command syntax consult the Navtelekom command reference for the precise command format. Placeholders such as [apn] or [apnu] may appear in manufacturer examples and represent the APN name and APN username respectively and should be replaced with your carrier values when required.

Configuration Notes​

  • Firmware differences may change available fields, command syntax, or UI layout in NTC Configurator or DRC; always check the device firmware version before applying procedures.
  • Choose UDP for lower overhead and slightly faster delivery in many networks, or TCP if you require session reliability; both transports are accepted by Plaspy on port 8888.
  • On-device Complex Events can reduce the volume of messages sent to Plaspy by filtering locally generated events before reporting.
  • Dual SIM redundancy improves uptime but verify that the active SIM has a working APN and data plan for IP reporting.
  • Keep a record of applied settings and firmware revisions to aid troubleshooting if a device does not appear in Plaspy after configuration.

Why Use Plaspy with This Configuration​

Using the Navtelekom СМАРТ S-4535 with Plaspy gives fleet operators visibility into real-time location, CAN bus telemetry, and event-driven alerts through a centralized platform. The tracker’s on-board logic and multiple I O interfaces allow you to collect rich vehicle data while relying on Plaspy to map and present that data for monitoring, reporting, and operational workflows.

Learn more about Plaspy and how this configuration supports fleet tracking and telemetry at https://www.plaspy.com. Device specific configuration methods, firmware behavior, and manufacturer details can change over time so verify the latest setup instructions on the official Navtelekom website https://www.navtelecom.ru/.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy