Skip to main content

Navtelekom - СМАРТ S-4537 Configuration

This page covers the public configuration context for using the Navtelekom СМАРТ S-4537 tracker with Plaspy. It summarizes the practical server settings, preparatory checks, and typical steps integrators use when pointing the S-4537 to Plaspy for real-time tracking and telemetry collection. Use this guide as a platform-focused reference; manufacturer tools and firmware versions determine exact device-side steps.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, so the same endpoint and port are used for many tracker models. Exact manufacturer-side setup steps can vary by firmware revision, hardware revision, installation type, and the configuration tool you use (for example NTC Configurator and DRC remote management are commonly used with this model). Always cross-check with the latest Navtelekom documentation when available.

Configuration Overview​

The aim of configuration is to prepare the СМАРТ S-4537 to send location and telemetry to Plaspy reliably and securely. Configuration covers server endpoint entry, transport selection, reporting parameters, and any on-device event logic needed for your deployment.

  • Point the device to the Plaspy server endpoint so it sends GNSS and CAN telemetry to the platform.
  • Select the transport protocol the device supports and confirm connectivity over cellular.
  • Configure reporting intervals and event rules so Plaspy receives meaningful real-time updates.
  • Verify SIM, power, and antenna connections to avoid intermittent data gaps during installation.
  • Validate visibility in Plaspy after configuration to ensure the device shows live updates and telemetry.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888 (Plaspy uses the same port for all supported devices)
  • Transport support for UDP or TCP (the device may be configured to use UDP or TCP on port 8888)
  • Plaspy automatically detects the tracker protocol when the device connects

These exact values are the public Plaspy endpoint settings to use when configuring the tracker to report to Plaspy.

Typical Requirements Before Setup​

  • A powered and installed СМАРТ S-4537 with antennas and backup battery connected according to the installer guide.
  • Active cellular connectivity and at least one working SIM inserted for the 4G modem and dual-SIM failover.
  • Access to the official manufacturer configuration method such as NTC Configurator or another Navtelekom tool.
  • The Plaspy server settings (d.plaspy.com or 54.85.159.138 and port 8888) available to the installer.
  • Administrative access to Plaspy account or fleet workspace to verify device visibility after configuration.
  • Knowledge of any required firmware or device-specific setup steps from Navtelekom for your hardware revision.

How This Tracker Connects to Plaspy​

The СМАРТ S-4537 sends GNSS positions and collected telemetry over its integrated 4G modem to the Plaspy endpoint and port. Plaspy receives those packets and applies automatic protocol detection so devices appear in the platform without custom protocol selection on the server side.

  • The tracker reports GNSS position and time stamped telemetry to d.plaspy.com on port 8888.
  • CAN bus telemetry from Engine and Comfort buses is captured locally and sent to Plaspy for dashboarding and reports.
  • Digital inputs, outputs, RS-485 MODBUS data, and 1-Wire sensor values are forwarded to Plaspy as configured events and telemetry.
  • Transport may be UDP or TCP depending on device configuration; ensure the chosen transport is set to use port 8888.
  • Plaspy automatically detects the tracker protocol when the device connects to the shared endpoint.

Common Configuration Workflow​

  1. Access the official Navtelekom configuration method or software such as NTC Configurator or your approved manufacturer tool.
  2. Open the networking or server settings area for the device you are configuring.
  3. Enter the Plaspy server endpoint using d.plaspy.com or the server IP 54.85.159.138 as provided.
  4. Set the server port to 8888.
  5. If the device requires a transport selection, choose UDP or TCP and set the port to 8888 for that transport.
  6. Apply or save the configuration on the device and upload or send settings using the manufacturer tool.
  7. Restart the device if required by the firmware or configuration tool to activate the new server settings.
  8. Validate in Plaspy that the device appears online and is reporting GNSS and telemetry data.

Example Configuration Commands​

The exact configuration commands and syntax depend on the Navtelekom firmware and the configuration tool you use. Some deployments use NTC Configurator for GUI setup, while others accept SMS or direct configuration via manufacturer's utilities or remote management (DRC). Because commands differ by firmware and installer tool, follow the current Navtelekom guidance for your device revision.

If you use an SMS or CLI method provided by Navtelekom, preserve placeholders supplied by the manufacturer such as APN or username placeholders and replace them with your operator values. Always confirm the command syntax with Navtelekom documentation before applying changes.

Configuration Notes​

  • Firmware differences can change available parameters and command syntax; confirm the device firmware version and consult Navtelekom release notes.
  • TCP and UDP behavior differs for reliability and firewall traversal; choose the transport that fits your network and carrier behavior, but ensure the port is set to 8888.
  • Plaspy uses the same port for all supported devices and automatically detects the tracker protocol, which simplifies server-side setup.
  • If you perform SMS based setup or use a local configurator, test settings on one device before mass deployment.
  • Keep a record of applied settings and firmware versions for troubleshooting and future audits.

Why Use Plaspy with This Configuration​

Using the СМАРТ S-4537 with Plaspy provides a streamlined way to capture real-time location, dual-CAN telemetry, and peripheral sensor data in a single platform. For fleets and integrators, the combination of integrated 4G modem, dual-SIM resilience, and multiple interfaces (CAN, RS-485, 1-Wire, BLE) lets you centralize vehicle monitoring and operational alerts in Plaspy without adding extra gateway hardware.

Learn more about Plaspy and how it supports mixed fleets and telemetry workflows at https://www.plaspy.com. For the latest device specific configuration instructions, firmware details, and manufacturer tools for the СМАРТ S-4537, verify information on the official Navtelekom site https://www.navtelecom.ru/ as device behavior and setup methods can change with firmware and hardware revisions.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy