Skip to main content

Navtelekom - START S-2010 Configuration

This page provides the public configuration context for using the Navtelekom START S-2010 with Plaspy. It focuses on the practical, platform-level settings and steps required to point the tracker at Plaspy so devices can report position, inputs, and telemetry. Use this guide alongside the START S-2010 hardware documentation and Navtelekom configuration utilities for device-specific procedures.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when the device connects. Manufacturer-side setup steps can vary by firmware revision, hardware variant, installation type, and the vendor tools you use for local or remote configuration. This page covers the shared Plaspy endpoint and workflow that you will apply using Navtelekom tools such as the NTC Configurator, Bluetooth or USB local setup, or Navtelekom DRC for remote provisioning.

Configuration Overview​

Preparing a START S-2010 for Plaspy means configuring the device to report to Plaspy's shared server and validating connectivity so the unit appears in your Plaspy account. The process is practical and focused: set the server endpoint, confirm transport and port settings, apply the configuration, and verify the device is visible and reporting in Plaspy.

  • Configure the tracker to send data to the Plaspy server endpoint d.plaspy.com or the equivalent IP 54.85.159.138.
  • Ensure the device is set to use port 8888 and choose UDP or TCP transport if the tracker requires a transport selection.
  • Apply and save settings in the Navtelekom local tool or DRC remote provisioning system.
  • Validate that the tracker reports location and input telemetry to Plaspy and appears in your Plaspy account.
  • Use USB Type-C or Bluetooth 4.0 for local diagnostics and configuration before final deployment.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol when the device connects

Typical Requirements Before Setup​

  • A powered and wired START S-2010 properly installed with the required vehicle power connection.
  • Active 2G nano SIM card inserted and confirmed to have cellular coverage where the device will operate.
  • Access to local configuration methods such as USB Type-C, Bluetooth 4.0, or Navtelekom DRC remote management.
  • A Plaspy account and access to the Plaspy platform for device validation and monitoring.
  • NTC Configurator or other Navtelekom configuration utilities for device parameter changes.
  • Basic wiring knowledge to confirm ignition, door, and sensor connections are correct for telemetry reporting.

How This Tracker Connects to Plaspy​

The START S-2010 sends GNSS-derived location and I/O telemetry over its cellular connection to the Plaspy server endpoint on the shared port. Plaspy receives those messages, automatically detects the tracker protocol, and routes device data into mapping, alerts, and reporting features in the platform.

  • The tracker transmits position and timing data to d.plaspy.com (54.85.159.138) on port 8888.
  • Device telemetry and input states (ignition, door, analog input when used) are sent to the same Plaspy endpoint.
  • Choose UDP or TCP transport on the device if required; Plaspy accepts either on port 8888.
  • Plaspy automatically detects the incoming tracker protocol so no separate protocol selection is needed in the platform.
  • Once connected, Plaspy updates maps, event feeds, and historical logs for the device.

Common Configuration Workflow​

  1. Access the official Navtelekom configuration method for the START S-2010 such as USB Type-C with NTC Configurator, Bluetooth 4.0 pairing, or Navtelekom DRC remote provisioning.
  2. In the device server or network settings, enter the Plaspy server as d.plaspy.com or alternatively 54.85.159.138.
  3. Set the device server port to 8888.
  4. If the device requires transport selection, choose UDP or TCP according to your installation preference or network requirements.
  5. Apply or save the configuration in the Navtelekom tool or via DRC.
  6. Restart or power cycle the START S-2010 if the tool or firmware requires it to activate new settings.
  7. Validate the device appears and reports in Plaspy by checking recent location updates, input states, or telemetry in your Plaspy account.

Example Configuration Commands​

The START S-2010 can be configured using Navtelekom tools or the DRC remote management system rather than raw command lines in many cases. Exact command syntax and configuration steps vary by firmware version and the utility you use (NTC Configurator, Bluetooth tool, or DRC). Use the appropriate Navtelekom configuration utility to set the server to d.plaspy.com (or 54.85.159.138) and the port to 8888, and select UDP or TCP if prompted. If you require command line or SMS style commands, consult Navtelekom technical documents or the NTC Configurator help for the precise format supported by your firmware.

Configuration Notes​

  • Firmware variations and hardware revisions may change menu locations or exact parameter names in the Navtelekom tools; always confirm the parameter names before saving.
  • Remote provisioning via Navtelekom DRC can simplify bulk updates for fleets and keep firmware current while pointing devices to d.plaspy.com on port 8888.
  • Choose UDP for lower overhead and typical telemetry, or TCP where a reliable session is required; Plaspy accepts both transports on the same port.
  • Use USB Type-C or Bluetooth for local setup and diagnostics when cellular coverage is not available during provisioning.
  • Plaspy uses the same port for all supported devices and automatically detects the tracker protocol when a device connects, so platform-side settings do not need per-device protocol selection.

Why Use Plaspy with This Configuration​

Connecting the START S-2010 to Plaspy brings compact, installation friendly tracking into a consistent fleet management environment. With location, input events, and analog telemetry available from the START S-2010, Plaspy provides mapping, alerting, and reporting that help fleets and service providers monitor assets, respond to events, and maintain operational oversight.

To learn more about Plaspy and platform features for fleet tracking visit https://www.plaspy.com. For the latest device specific configuration steps, firmware notes, and technical resources from the manufacturer, verify details at the official Navtelekom site https://www.navtelecom.ru/.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy