Skip to main content

Navtelekom - START S-2012 Configuration

This page describes the public configuration context for using the Navtelekom START S-2012 tracker with Plaspy. It focuses on the practical, platform-level settings and workflow needed to forward GNSS location, sensor telemetry, and event data from the START S-2012 to Plaspy. The information here is intended to help installers and fleet teams prepare the device for integration with Plaspy using the manufacturer's configuration tools.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, but manufacturer-side steps can differ by firmware, hardware revision, installation type, and vendor tools. Navtelekom provides NTC Configurator and DRC remote management tools for device setup and maintenance; follow those vendor tools and the official Navtelekom documentation when applying the settings described on this page.

Configuration Overview​

The core of START S-2012 integration with Plaspy is pointing the tracker to the Plaspy server endpoint and confirming transport, then validating that GNSS and sensor data arrive in the platform. Plaspy uses a single shared port across all supported devices and will automatically detect the tracker protocol once the device is sending data to the correct endpoint.

  • Configure the tracker to send telemetry to the Plaspy server endpoint (domain or IP) on the shared Plaspy port.
  • Choose the transport option supported by the tracker (UDP or TCP) and verify connectivity.
  • Use NTC Configurator or DRC remote tools to persist the server settings on the device.
  • Validate real-time position, sensor telemetry, and event reporting within Plaspy after the device connects.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol once the device sends data to the shared Plaspy endpoint

Typical Requirements Before Setup​

  • A powered and hardwired START S-2012 unit installed according to Navtelekom wiring guidance.
  • Active cellular service for the device SIM card and verified coverage on the installation network.
  • Access to the manufacturer's configuration tools such as NTC Configurator or DRC remote management.
  • A Plaspy account or provisioning information so the device can be associated with the correct customer or fleet workspace.
  • Latest known firmware or a firmware level validated for compatibility where possible.
  • Physical access to the device during initial configuration or a method for remote configuration via the vendor tools.

How This Tracker Connects to Plaspy​

The START S-2012 uses its GSM connection to forward GNSS positions and sensor data to the Plaspy server endpoint and port. Once addressed to the Plaspy server, the platform will detect the tracker protocol automatically and begin parsing data for live tracking, events, and telemetry.

  • The device streams GNSS location reports to d.plaspy.com (or 54.85.159.138) on port 8888 using UDP or TCP.
  • Sensor and telemetry data such as fuel level, Bluetooth sensor readings, and event inputs are forwarded alongside location updates.
  • Event inputs and the control output can be used to generate alerts and remote commands visible in Plaspy.
  • Bluetooth sensor data and RS-485 or USB Type-C integrations are relayed to Plaspy by the device when configured and supported by firmware.
  • Plaspy receives the incoming stream and maps it to the appropriate device record once the tracker connects to the shared Plaspy port.

Common Configuration Workflow​

  1. Access the official Navtelekom configuration method such as NTC Configurator or DRC remote management to begin setup.
  2. In the server or telemetry settings enter the Plaspy server as either d.plaspy.com or the IP address 54.85.159.138.
  3. Set the destination port to 8888, the shared Plaspy port used by all supported devices.
  4. Choose the transport protocol (UDP or TCP) if the device requires explicit transport selection.
  5. Save or apply the configuration in the manufacturer's tool and allow the device to receive the updated settings.
  6. Restart or power-cycle the device if required by the manufacturer to activate the new server settings.
  7. Validate that the START S-2012 reports to Plaspy and that position, telemetry, and events appear in the Plaspy platform.

Example Configuration Commands​

The START S-2012 is typically configured with Navtelekom tools rather than requiring raw commands in the field. Exact commands and the user interface depend on the NTC Configurator or DRC firmware interface and may vary by firmware version and tool release. When configuring, set the server to d.plaspy.com or 54.85.159.138 and the port to 8888, choose UDP or TCP if prompted, then save and apply the settings through the vendor tool.

If you use a vendor method that exposes low level command syntax, follow the manufacturer's documented command format in NTC Configurator or DRC and retain any placeholders the tool requires. Refer to Navtelekom documentation for command examples specific to your firmware and toolset.

Configuration Notes​

  • Firmware differences can change menu names and the exact location of server and transport settings; confirm with the device firmware release notes.
  • Selecting TCP versus UDP can affect how the tracker batches or retries messages; choose the transport that matches your stability and latency needs.
  • When using Bluetooth sensors, ensure those peripherals are paired and visible to the tracker before relying on sensor telemetry in Plaspy.
  • Verify the SIM APN and cellular registration via the manufacturer tool if the device cannot reach the Plaspy server.
  • Use the manufacturer's NTC Configurator and DRC for remote management and to reduce physical visits for firmware updates or bulk provisioning.

Why Use Plaspy with This Configuration​

Using the START S-2012 with Plaspy provides a compact, hardwired tracking solution that delivers GNSS positions and rich telemetry into a single fleet management platform. For fleets that need discreet installations, fuel monitoring, environmental sensor data, and event-based alerts, the START S-2012 paired with Plaspy enables unified visibility and operational oversight.

To learn more about Plaspy and how it can accept START S-2012 data, visit https://www.plaspy.com. Please verify current device-specific configuration methods, firmware behavior, and detailed installation instructions on the manufacturer's site https://www.navtelecom.ru/ as equipment capabilities and setup procedures can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy