Skip to main content

OKB Tehnoavtomatika - AAP PERSONAL Configuration

This page documents the public configuration context for using the OKB Tehnoavtomatika AAP PERSONAL tracker with the Plaspy platform. It gathers the practical server settings and setup workflow that you will need to point an AAP PERSONAL device at Plaspy so the device can report location and status. The guidance here is built around Plaspy server endpoints and common manufacturer configuration practices rather than proprietary or private service credentials.

Plaspy uses shared server settings across supported devices and it automatically detects the tracker protocol once the device is reporting to Plaspy. Exact manufacturer side steps for configuring the AAP PERSONAL can vary by firmware version, hardware revision, installation type, and vendor tools. Use this page to align the AAP PERSONAL with Plaspy server values and then verify the device behavior with the manufacturer documentation and tools.

Configuration Overview​

The goal of this configuration process is to prepare an AAP PERSONAL tracker to send its telemetry to Plaspy so the device is visible and manageable on the platform. The AAP PERSONAL supports GPRS and SMS reporting and runs on DC GSM 900 1800 bands with an internal battery, which makes it suitable for remote monitoring tasks. Pointing the device at Plaspy is primarily about setting the correct server endpoint, transport, and port and then validating the device can reach Plaspy.

  • Configure the tracker to report to Plaspy by entering the Plaspy server endpoint and the common Plaspy port
  • Set the transport protocol to UDP or TCP if required by the device firmware
  • Ensure GPRS connectivity and correct APN credentials for internet reporting from the device
  • Save the device configuration and restart the tracker if required to initiate connections to Plaspy
  • Validate the tracker is visible in Plaspy after it begins reporting to the shared server

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol when the device connects
  • All devices in Plaspy use the same port so use port 8888 for AAP PERSONAL reporting

Typical Requirements Before Setup​

  • A charged and functional AAP PERSONAL device with access to the manufacturer configuration method
  • A valid SIM card with a data plan and GPRS enabled when using internet based reporting
  • APN credentials available from the mobile operator if GPRS reporting is required
  • Access to the OKB Tehnoavtomatika configuration utility or the documented SMS command set for the AAP PERSONAL
  • A computer or phone to edit settings and apply configuration to the device
  • Basic network reachability so the device can resolve and connect to d.plaspy.com

How This Tracker Connects to Plaspy​

The AAP PERSONAL sends location and status updates to the Plaspy server endpoint using GPRS data or fallback SMS reporting depending on how it is configured. Once the device is pointed at the Plaspy server endpoint and port, Plaspy will detect the tracker protocol and process incoming messages so the device becomes visible in the platform.

  • The device is configured to report to the shared Plaspy server endpoint d.plaspy.com or the server IP 54.85.159.138
  • Communications use port 8888 which is the common Plaspy port for all supported devices
  • The tracker may use UDP or TCP transport depending on firmware options and configuration; Plaspy accepts either
  • Plaspy automatically detects the tracker protocol and decodes telemetry once data arrives
  • Reporting can include periodic location updates and event notifications as supported by the device and firmware

Common Configuration Workflow​

  1. Access the official OKB Tehnoavtomatika configuration method or software for the AAP PERSONAL, or use the documented SMS command set if supported
  2. Enter the Plaspy server endpoint by hostname d.plaspy.com or by IP address 54.85.159.138 in the server field
  3. Set the server port to 8888 which is the shared Plaspy port for all devices
  4. Choose UDP or TCP as the transport protocol if the device requires a transport selection
  5. Configure APN and GPRS settings on the device if internet reporting is used, or verify SMS settings if SMS is required for your deployment
  6. Apply or save the configuration in the device interface or send the SMS configuration commands as instructed by the manufacturer
  7. Restart the device if required by the configuration tool or firmware to activate the new server settings
  8. Validate that the device reports to Plaspy by checking device visibility in Plaspy and confirming incoming data is received

Example Configuration Commands​

The AAP PERSONAL is typically configured either with the manufacturer software tool or via SMS commands depending on firmware. Exact commands and syntax vary with firmware versions and vendor supplied utilities, so there are no universal commands included here. When using the manufacturer SMS method or configuration tool, use the Plaspy server values:

  • Server hostname d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport UDP or TCP as required

Refer to the official OKB Tehnoavtomatika user manual or configuration guide for the precise SMS or utility commands to set server, port, transport, and APN. If you obtain public command examples from the manufacturer, apply them in the order recommended by OKB Tehnoavtomatika and include any required placeholders exactly as provided.

Configuration Notes​

  • Firmware differences may change available configuration options such as whether transport is selectable or fixed by firmware
  • SMS based configuration can be useful when GPRS is not available, but confirm the SMS command set and syntax with OKB Tehnoavtomatika
  • Choose UDP or TCP based on device support and network conditions; both transports are accepted by Plaspy on port 8888
  • Verify APN credentials and cellular registration on the device before expecting GPRS reporting to Plaspy
  • Market variations and hardware revisions can change default behavior; always check the manufacturer documentation for your device serial number and firmware version

Why Use Plaspy with This Configuration​

Using Plaspy with the AAP PERSONAL gives organizations a practical way to centralize location and status reporting from battery powered personal trackers that operate in remote or mobile scenarios. By pointing the device at Plaspy and using the shared server and port settings, you can consolidate telemetry from multiple devices and rely on Plaspy to detect and decode the tracker protocol.

To learn more about Plaspy and platform capabilities visit https://www.plaspy.com. For the latest device specific setup details firmware notes and official command references verify information on the manufacturer website http://www.okb-ta.ru/

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy