Skip to main content

OKB Tehnoavtomatika - MPU-01GLONASS Configuration

This page provides the public configuration context and practical guidance for using the OKB Tehnoavtomatika MPU-01GLONASS tracker with the Plaspy platform. It summarizes the shared Plaspy server settings you must apply on the device and explains the typical steps installers and integrators follow to bring the tracker online. The device description used here is based on the public product details for the MPU-01GLONASS including its compact form factor, GLONASS GPS receiver, GSM 900 and 1800 support, SMS capabilities, and its configurable input output options.

Plaspy uses shared server settings across supported trackers and automatically detects the tracker protocol when the device connects. Manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and vendor configuration tools, so you should follow OKB Tehnoavtomatika documentation or vendor guidance for device specific instructions while applying the Plaspy server values listed below.

Configuration Overview​

Configuring the MPU-01GLONASS for Plaspy is primarily about pointing the tracker at Plaspy server endpoints and validating end to end connectivity so the device appears and reports correctly in the platform. The process covers setting the server endpoint and port, selecting the transport if required, and verifying that data and status messages reach Plaspy.

  • Set the tracker reporting endpoint to the Plaspy server so location and status messages are routed to the platform
  • Select UDP or TCP transport on the device if the configuration interface requires a transport choice
  • Ensure the tracker has power, an active cellular SIM where required, and manufacturer access for configuration
  • Save and apply the configuration and restart the device when prompted to start reporting to Plaspy
  • Verify the device appears in Plaspy and that location updates are received and parsed correctly

Plaspy Server Settings​

Use these public Plaspy connection values when configuring the MPU-01GLONASS. Plaspy uses the same port for all supported devices and automatically detects the tracker protocol when the device connects.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP depending on the tracker configuration method
  • Plaspy automatically detects the tracker protocol when the device connects
  • All devices in Plaspy use the same port for device reporting

Typical Requirements Before Setup​

  • Device powered and accessible for configuration and testing
  • Active cellular SIM with carrier service as required by the installation and device firmware
  • Mobile network coverage on GSM 900 or 1800 bands at the installation site
  • Access to the official OKB Tehnoavtomatika configuration method or software and any vendor tools used for this model
  • Basic knowledge of the device input output mapping if you plan to enable or test digital or analog inputs
  • Plaspy account or platform access to validate that the device is visible and reporting after configuration

How This Tracker Connects to Plaspy​

When configured for Plaspy, the MPU-01GLONASS sends its location and status messages to the shared Plaspy server endpoint and port. Plaspy receives the incoming data and automatically determines the device protocol so minimal per device protocol selection is required on the platform side.

  • The tracker reports to d.plaspy.com or 54.85.159.138 on port 8888
  • Transport can be UDP or TCP depending on the tracker setting and installer choice
  • Location and device events are transmitted to Plaspy where the platform parses and presents the data
  • SMS can be available on the device for messaging and may be used by installers for remote commands or fallbacks depending on firmware
  • Plaspy will detect the tracker protocol automatically when the device connects to the server endpoint

Common Configuration Workflow​

  1. Access the official OKB Tehnoavtomatika configuration method or software provided for the MPU-01GLONASS
  2. Enter the Plaspy server address using either d.plaspy.com or 54.85.159.138 as the device server endpoint
  3. Set the server port to 8888 which is used by Plaspy for all supported devices
  4. Choose UDP or TCP on the tracker if the configuration interface requires a transport selection
  5. Apply or save the configuration on the device and follow any device prompts to confirm changes
  6. Restart the device if required by the firmware to begin reporting to the new server settings
  7. Validate that the device reports to Plaspy and appears in the platform with expected location updates and status

Example Configuration Commands​

The exact command syntax and configuration interface for the MPU-01GLONASS depend on the manufacturer toolset and firmware version. OKB Tehnoavtomatika devices are commonly configured via dedicated configuration software or SMS command strings supplied by the manufacturer. Because command formats vary by firmware, consult the official device manual for precise commands. Typical tasks include setting the server address to d.plaspy.com or 54.85.159.138 and assigning port 8888 while selecting UDP or TCP if needed.

Configuration Notes​

  • Firmware differences can change available configuration options and command syntax between device revisions
  • Choose UDP or TCP deliberately based on installation needs and the device configuration interface; Plaspy accepts both transports on port 8888
  • SMS based setup or remote commands may be supported by the device for basic configuration or troubleshooting depending on firmware
  • Confirm digital and analog input mapping in the manufacturer documentation before enabling inputs to ensure expected behavior in Plaspy
  • Always verify that the device firmware is appropriate for your deployment and that you are using the correct manufacturer tool or command set

Why Use Plaspy with This Configuration​

Using the MPU-01GLONASS with Plaspy provides a straightforward path to fleet and asset visibility by directing tracker reports to a single, shared Plaspy server endpoint. The shared port and automatic protocol detection in Plaspy reduce per device complexity and help speed up deployments where many devices must be registered and monitored.

To learn more about Plaspy and how the platform handles device connections and data, visit https://www.plaspy.com. For the most current device specific configuration instructions, firmware notes, and official command lists consult the OKB Tehnoavtomatika website at http://www.okb-ta.ru/ since manufacturer specifications and setup methods can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy