Skip to main content

OKB Tehnoavtomatika - MTA-02 Configuration

This page documents the public configuration context for using the OKB Tehnoavtomatika MTA-02 with Plaspy. It consolidates the server settings, practical setup guidance, and verification steps that are routinely required to register and operate MTA-02 trackers on the Plaspy platform. The content here focuses on shared, public information useful for installers and technical teams preparing the device for platform visibility.

Plaspy uses shared server settings for supported devices and performs automatic protocol detection to simplify integration. Manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and vendor configuration tools, so use this guide to apply the common Plaspy settings and then consult OKB Tehnoavtomatika documentation for device specific commands and wiring.

Configuration Overview​

Successful configuration prepares the MTA-02 to communicate reliably with the Plaspy server and appear in the Plaspy interface. Typical configuration work aligns the device network parameters, transport protocol, and reporting settings so Plaspy can automatically interpret incoming data.

  • Point the tracker to the Plaspy server endpoint so location and events are routed to the platform
  • Select the transport protocol the device supports and confirm Port 8888 is set
  • Verify network connectivity and APN settings for GPRS based reporting when applicable
  • Save and restart the device so settings take effect and the tracker begins reporting
  • Confirm the device is visible in Plaspy and that events or position updates appear

Plaspy Server Settings​

When configuring MTA-02 for Plaspy, use the following public server settings exactly as listed. Plaspy uses the same port for all supported devices and the platform automatically detects the tracker protocol.

  • server domain d.plaspy.com
  • server IP 54.85.159.138
  • port 8888
  • transport support for UDP or TCP
  • automatic protocol detection in Plaspy

Typical Requirements Before Setup​

  • Confirm the MTA-02 is powered and accessible to the installer either in a bench setup or installed location
  • Have a valid SIM card with a data plan and correct APN information if using GPRS reporting
  • Obtain the manufacturer configuration method or software for the specific MTA-02 firmware or hardware revision
  • Ensure you can set the device reporting host to d.plaspy.com or 54.85.159.138 and the port to 8888
  • Be prepared to select UDP or TCP if the device requires explicit transport selection
  • Access to tools to monitor initial network registration and to review SMS messages if the device supports SMS based commands

How This Tracker Connects to Plaspy​

The MTA-02 is configured to report position and event data to a central Plaspy endpoint so the device appears on the Plaspy platform for monitoring and analysis. Plaspy receives the data on a single shared port and determines the protocol automatically to simplify onboarding.

  • The device sends location and event packets to d.plaspy.com or 54.85.159.138
  • Packets are received on port 8888 which Plaspy uses for all supported trackers
  • The installer chooses UDP or TCP transport when required by the device
  • Plaspy automatically detects the tracker protocol and maps incoming data to the platform
  • Once reporting begins, positions and alerts become visible in Plaspy for operational monitoring

Common Configuration Workflow​

  1. Access the official OKB Tehnoavtomatika configuration method or software for the MTA-02, following the device manual and vendor tools
  2. In the device settings, enter the Plaspy host as d.plaspy.com or as the IP 54.85.159.138
  3. Set the reporting port to 8888 exactly as provided by Plaspy
  4. Choose UDP or TCP transport if the MTA-02 requires transport selection
  5. Configure any required APN, username, or password for GPRS data if the device will use mobile data
  6. Apply or save the configuration and restart the device if the device firmware requires a reboot
  7. Validate that the device reports to Plaspy by observing incoming updates on the Plaspy platform or by checking device diagnostics

Example Configuration Commands​

The public configuration for MTA-02 can differ by firmware and the manufacturer tool used. No specific device command strings are provided here. Exact commands and SMS or serial configuration strings depend on the MTA-02 firmware and the vendor configuration utility. Refer to the official OKB Tehnoavtomatika documentation or the device configuration tool supplied by your vendor to obtain the exact commands for setting the server host to d.plaspy.com or 54.85.159.138 with port 8888 and selecting UDP or TCP transport.

If you have a command list from OKB Tehnoavtomatika for your firmware, apply the host and port settings in the order the manufacturer specifies, preserve placeholders for APN or credentials, and follow any optional reboot steps the manufacturer recommends.

Configuration Notes​

  • Firmware and hardware revisions can change the configuration interface or the exact command syntax for MTA-02, so confirm commands match your device version
  • Choosing TCP or UDP can affect delivery semantics; use the transport required or recommended for your environment
  • APN, APN user, and APN password are typically required for GPRS reporting if using mobile data; keep these values ready when configuring the device
  • If SMS based configuration is supported, verify the exact SMS command format with OKB Tehnoavtomatika documentation
  • Always confirm settings by checking that the device successfully registers and sends data to the Plaspy server endpoint

Why Use Plaspy with This Configuration​

Connecting the MTA-02 to Plaspy gives organizations centralized visibility into device locations and event reporting. Using Plaspy simplifies operations by leveraging a single shared port and automatic protocol detection so trackers like the MTA-02 can be integrated with fewer protocol selection steps and consistent server settings.

To learn more about Plaspy and platform capabilities visit https://www.plaspy.com. For the latest device specific configuration methods, firmware behavior, and manufacturer details verify current information at http://www.okb-ta.ru/

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy