Skip to main content

Pointer - Cello Track 8M Configuration

This page covers the public configuration context for using the Pointer Cello Track 8M family with Plaspy. It summarizes the practical server settings and workflow you will use when integrating a CelloTrack 8M device into the Plaspy platform. The content here focuses on the shared, public settings that Plaspy requires and on the general steps for preparing and validating the device connection.

Plaspy uses shared server settings across supported devices and can automatically detect the tracker protocol when the device reports to the platform. Exact manufacturer side setup steps can vary depending on firmware version, hardware revision, installation type, and vendor configuration tools, so follow the manufacturer guidance alongside the Plaspy settings below.

Configuration Overview​

The goal of configuration is to prepare the Cello Track 8M for reliable communication with Plaspy so devices report location and status to the platform. Use the manufacturer configuration interface or SMS/software tools to point the device at the Plaspy server and verify transmissions.

  • Configure the device network endpoint to report to Plaspy so data reaches the platform.
  • Ensure APN and mobile data are valid for GPRS transmissions if the device uses cellular data.
  • Select transport settings such as UDP or TCP if the device requires a transport choice.
  • Save and apply settings, then verify the device appears in Plaspy and reports expected messages.
  • Validate regular reporting and event visibility in Plaspy after the initial setup.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol so the platform accepts supported protocols on the same port

Typical Requirements Before Setup​

  • A charged and functioning Cello Track 8M device from Pointer ready for configuration
  • Access to the official Pointer configuration method or software supplied by the vendor
  • A working data SIM with a valid APN if the device transmits using GPRS
  • The device IMEI or identifier for registration and verification in Plaspy
  • Basic connectivity test tools or a device console to confirm outbound packets reach the Plaspy server
  • Knowledge of whether your installer tools require choosing UDP or TCP when specifying the server

How This Tracker Connects to Plaspy​

The Cello Track 8M family sends GPS and status information to the Plaspy server endpoint so that points and events are visible in the platform. Configuration points the tracker at the Plaspy server and port, and Plaspy will handle protocol detection and message parsing for supported tracker protocols.

  • Device is configured to report to the shared Plaspy server endpoint and port
  • Tracker uses GPRS transmissions to send location and device messages to Plaspy
  • Plaspy receives and automatically detects the protocol then ingests device data
  • Once reporting, the device becomes visible in Plaspy for monitoring and historical playback
  • Regular transmissions and event updates allow operational monitoring and alerts in Plaspy

Common Configuration Workflow​

  1. Access the official Pointer configuration method or software provided by the manufacturer or vendor.
  2. Enter the Plaspy server as either the domain d.plaspy.com or the IP address 54.85.159.138 in the device server field.
  3. Set the device port to 8888, which Plaspy uses for all supported devices.
  4. Choose UDP or TCP if the device requires a transport selection in its configuration interface.
  5. Confirm APN and mobile data settings are correct for the SIM in the device so GPRS transmissions can occur.
  6. Apply or save the configuration and restart the device if the manufacturer tool or firmware recommends a reboot.
  7. Validate that the device reports to Plaspy and appears in the platform with expected location updates.

Example Configuration Commands​

The exact command syntax and configuration messages vary by Pointer firmware and the vendor tool used to program the Cello Track 8M. Because the manufacturer provides different utilities and command formats depending on firmware, there are no universal public commands included here. Use the Pointer configuration utility or the official device manual to obtain the precise commands or SMS strings required for your firmware revision.

If you have a manufacturer provided command list, apply the commands in the order specified by Pointer and include the Plaspy server settings:

  • d.plaspy.com or 54.85.159.138 as the server
  • port 8888
  • choose UDP or TCP as transport when required

Configuration Notes​

  • Firmware and hardware revisions can change required command syntax or configuration menus; always check Pointer documentation for firmware specific instructions.
  • Plaspy uses the same port 8888 for all supported devices and automatically detects tracker protocol, so the server and port are consistent across integrations.
  • Selecting UDP versus TCP may affect message delivery behavior depending on the tracker firmware; choose the transport the device supports and test for reliability.
  • Confirm the APN and mobile data settings with your SIM provider before testing transmissions from the device.
  • Installer and vendor tools may expose either a domain field or an IP field; you can use either d.plaspy.com or 54.85.159.138 as supported.

Why Use Plaspy with This Configuration​

Using the Pointer Cello Track 8M with Plaspy gives organizations a straightforward path to capture asset location and status using the shared Plaspy server infrastructure. The combination of a low power device family like the CelloTrack 8M and Plaspy server handling simplifies deployment for long battery life monitoring and periodic GPRS reporting.

To learn more about the Plaspy platform and how it supports tracker integrations, visit https://www.plaspy.com. For the most current device specific setup details, firmware instructions, and manufacturer guidance for the Cello Track 8M family, verify documentation on the Pointer website http://www.pointer.com.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy