Skip to main content

Protrack - GT06N Configuration

This page documents the public configuration context for using the Protrack GT06N with Plaspy. It summarizes the practical server settings and the common manufacturer commands used to point the GT06N at Plaspy so the device can report location and status into the Plaspy platform.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while the exact manufacturer side setup steps can vary by firmware version, hardware revision, installation method, and vendor tools. When available, this page includes the GT06N SMS commands commonly used for configuration; always confirm device specific details with the manufacturer documentation.

Configuration Overview​

This configuration prepares the GT06N to connect to Plaspy so the tracker sends position and event messages to the platform. The process typically involves setting the carrier APN, configuring the Plaspy server endpoint and port, selecting the transport type if required, and verifying that the device reports successfully.

  • Provide the GT06N with the correct carrier APN so GPRS data can be used for telemetry.
  • Configure the device to report to the Plaspy server endpoint so location and events are delivered to Plaspy.
  • Choose UDP or TCP transport if the device asks, using the shared Plaspy port.
  • Set update intervals and reporting timers to match your monitoring needs and data plan.
  • Validate connectivity and status using the device verification commands so the tracker appears in Plaspy.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol and uses the same port for all supported devices

Typical Requirements Before Setup​

  • A powered and installed GT06N device with access to the device SMS configuration method or manufacturer configuration tool.
  • A working SIM card with data service and the carrier APN information required to enable GPRS connectivity.
  • The carrier APN, and if required, APN username and password values ready for configuration.
  • Access to the Protrack documentation or vendor support for any firmware specific commands or behavior.
  • A Plaspy account or organizational setup so devices can be validated once reporting begins.
  • Ability to send and receive configuration SMS messages from the installing technician or configuration phone.

How This Tracker Connects to Plaspy​

The GT06N is configured to send location and event data to the Plaspy endpoint so Plaspy can ingest telemetry for live maps, alerts, and reporting. By pointing the tracker to the shared Plaspy server and port, the device becomes visible and manageable inside the Plaspy platform.

  • The device reports GPS positions and event messages to d.plaspy.com on port 8888.
  • Plaspy accepts connections over UDP or TCP depending on device selection and firmware capability.
  • Plaspy automatically detects the tracker protocol so devices can be recognized without manual protocol selection in the platform.
  • Once the tracker reports to the shared server endpoint, location, SOS, geofence, overspeed, and status events become visible in Plaspy.
  • Confirming device status and parameters helps ensure reliable visibility and alerting inside Plaspy.

Common Configuration Workflow​

  1. Access the official Protrack configuration method for the GT06N, typically SMS commands or vendor software, and confirm the firmware version if possible.
  2. Enter the Plaspy server by name or IP using d.plaspy.com or 54.85.159.138 as the server endpoint.
  3. Set the server port to 8888, which is the shared port Plaspy uses for all devices.
  4. Choose UDP or TCP transport if the GT06N requires a transport selection during setup.
  5. Configure the carrier APN and any APN username or password placeholders required by your SIM.
  6. Apply or save the configuration on the device and restart the tracker if required by the manufacturer.
  7. Validate that the device is reporting to Plaspy by checking device status and ensuring the tracker appears in the Plaspy dashboard.

Example Configuration Commands​

The GT06N supports SMS based configuration. Below are commonly used SMS commands in the typical order required for setup. Replace placeholders as noted.

  • Configure your carrier APN

    • Use this command to set the APN. Replace [apn] with the carrier APN. If your APN requires a username and password, include [apnu] and [apnp] where shown.
    APN,[apn]#

    or with username and password:

    APN,[apn],[apnu],[apnp]#

    Explanation: [apn] = carrier APN, [apnu] = APN username if required, [apnp] = APN password if required.

  • Setup the GPRS server to report to Plaspy

    SERVER,1,d.plaspy.com,8888,0#

    Explanation: This points the device to d.plaspy.com on port 8888. The parameters after the server address depend on device firmware; keep the order shown.

  • Set the location update interval

    TIMER,60,60#

    Explanation: Sets reporting intervals. Replace the numeric values as required by your reporting policy and data plan.

  • Enable GPRS mode

    GPRSON,1#

    Explanation: Switches the tracker to use GPRS mode for data reporting.

  • Check current configuration

    PARAM#

  • Check device status

    STATUS#

Keep the command order when it is important for enabling data reporting. If you must perform a reset or firmware specific initialization, label that step as optional and consult Protrack documentation before proceeding.

Configuration Notes​

  • SMS based configuration is supported for the GT06N in many firmware builds; always confirm the exact syntax for your firmware revision with Protrack materials.
  • The choice between UDP and TCP depends on installer preference and device firmware; both transports are supported to reach d.plaspy.com on port 8888.
  • Plaspy uses the same port for all supported devices and automatically detects the tracker protocol, reducing platform side configuration.
  • Verify APN credentials with the mobile carrier before deploying to avoid connectivity delays.
  • Firmware differences and vendor tools can change command syntax or available features; review the official Protrack documentation when in doubt.

Why Use Plaspy with This Configuration​

Using the GT06N with Plaspy gives organizations practical visibility and control over vehicle fleets and personal vehicles. Pointing the tracker at the shared Plaspy endpoint provides consistent data ingestion into the platform so teams can monitor locations, receive SOS and geofence alerts, audit routes, and act on immobilizer or other security events when configured.

To learn more about Plaspy and how this configuration fits into a broader telematics deployment visit https://www.plaspy.com. Please verify device specific configuration methods and the latest firmware details with the manufacturer at http://www.protrackgps.in/ since manufacturer setup steps and firmware behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy